Question about Televison & Video

1 Answer

Mitsubishe wd-65732. Air flow problem. How do I clean the air filter?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,617 Answers

There is an access panel on the side of the television the air filter is behind that panel with the air vents

Posted on May 04, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Says I need to fix airflow problem


It is telling you that the unit is overheating for a lack of air flowing over the globe. Check that the air slots are not blocked. the fan motor is working and any filters are clean and not blocked.

Apr 07, 2013 | Mitsubishi WD-62525 62" Rear Projection...

2 Answers

My mitsubishi wd-65c8 has a flashing green light.. I have replaced the capacitors on the DM board and the same is happening.. what else could be the...


Common Repairs
For the following models: WD-52631, WD-57731, WD-65731, WD-Y57, WD-Y65, WD-57732, WD-65732, WD-57831, WD-65831, the most common repair problem stems from television shutting off almost immediately after it has been turned on accompanied by the message, "TV will shut down in a few seconds. Please check if the air flow is blocked." According to the Mitsubishi website, this issue is caused by a loose connection as a result of a faulty thermal sensor. For models: WD-73727, WD-73827, WD-73927, WD-73732, WD-7383, the most encountered repair problem has been in relation to the optical engine. Another common situation consumers have encountered is failure of the TV to turn on along with unceasing flashing of the green power light. The solution for this problem, caused by the DM board, will vary by repairman. Consumers have also encountered issues with moving vertical or horizontal lines appearing on the screen which can either be due to problems with the capacitor, light engine, or formatter board. Make sure all bad caps are changed.

Jan 23, 2011 | Mitsubishi WD-65C8 65 in. LCD HDTV

1 Answer

I have a 2006 WD 65732.just replaced the lamp,still have white haze around,pepole and words.could it be a seal?


Quite possibly the lens is in need of a clean. It sounds like it is acting a bit like when you see a moon on a night with high cloud, we see a ring around it caused by the atmosphere, much the same as dust on the lens.
Hope that helps.

Dec 31, 2010 | Mitsubishi WD-65732 65" Projection HDTV

2 Answers

Starts but won't stay running, i clean carburator and still have same problem, unit has been used very little, still look new, Thanks,


Have you checked your oil? You need pump oil half way up in reservoir. Open plug on top of pump and check oil. Pump takes SAE 20 or 30

Next, open oil plug below engine and check your oil level. It should come up 1/2 way on dip stick. Engine takes 10W30. Don't turn washer on its side or upside down to drain oil or oil will run into carburetor.

Is the water turned on? Are you holding gun trigger open while starting? Pump needs water flow. DO NOT tie gun trigger open with wire and then start engine. That gun will flip around and shoot a hole in your leg.

If the engine starts, then you have gas, spark and compression

If engine won't stay running, the exhaust port might be clogged, or the carburetor is not letting in enough gas, or gas is not flowing to carburetor.

Check the screen over exhaust port > is it dirty or clogged? Clean with WD-40 or break it out with a screwdriver.
Remove gas filter below gas tank >>> it has a hex bolt >> loosen bolt >> the gas should come flowing out >> put it back if gas comes out
Next remove rubber gas line feeding gas to carburetor >> gas should flow out this line too >> if flows then put it back.

What about your air filter? Take it off. See if engine fires and runs without air filter. Air filter may be clogged.

While air filter is out, you can see open port to carburetor. Spray some WD-40 into carburetor. Fire up the engine. It should spark real healthy on the WD-40. Keep spraying WD-40 into carburetor to see if you can keep engine going. Don't forget to keep gun trigger open so water is flowing and pressure is not building in pump.

If engine keeps going with WD-40 but dies without it, then your carburetor is very suspect. You might need a new one.

If engine will not keep going with WD-40, then the spark is very suspect.

Change spark plug. Try again. If it doesn't fire up after that, you need to take it to the shop for repair.

Oct 09, 2010 | Honda 2500 PSI Gas Pressure Washer

1 Answer

How can I tell if its my thermal sensor causing aif flow problem and tv shutting off I have WD-65732


If the TV turns off after a short period of time, then it's most likely a heating problem. Any potentially hazardous electronic device will shut off when it senses too much heat. I'm not sure about a thermal sensor causing air flow problems, though. It's simply there to shut the whole thing down in case of emergencies.
There may be another explanation, such as there's a dead fan or a dislodged heat sink. Maybe it's even that the ambient temperature is too much for it to run, though usually these things are designed to run in just about any climate.
You'd have to open this one up and look at where all of the heat sinks are, as well as the fan. If no heat sinks are dislodged, then carefully turn the set on and make sure that any and all fans are operating as they should. Sometimes you just have to clean them out because of a build-up of dust,
Just be careful, as LCD TVs have a backlight board that goes up to at least 330V. Just make sure to not touch it while it's running.

Jun 08, 2010 | Mitsubishi WD-65732 65" Projection HDTV

1 Answer

WD-65732 has audio but no picture. Sound like


Replace Lamp Call Mats Electronics 1-800-628-1118

Mar 25, 2010 | Mitsubishi WD-65732 65" Projection HDTV

2 Answers

Air flow problem


Pull Lamp Out and see if when you try to turn it on if the Ballast Board has a spark/arking noise coming from it? If So Replace the Lamp.

Jan 14, 2010 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Tv says air flow problems


ok what you have there is a faulty thernal sensor nitisubishi has issuued a bullitten to serice centers so check with local service center the repair might be covered under warennty

Jun 18, 2009 | Mitsubishi WD-Y65 65" HDTV

2 Answers

Mitsubishi DLP overheating


check your air intake filters, it's a removeable filter in the air inlets.

May 04, 2008 | Televison & Video

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

425 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72670 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...