Question about Projection Televisions

1 Answer

I need to know the exact type of ac power cord for a Hisense TL2020.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 6,966 Answers

Hi,

To my knowledge, a Hisense TL2020 uses an IEC320C13 to NEMA 5-15P. It is the same type of AC power cord with those used by computers. Of course the plug itself would have to conform with your country's electrical code.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Posted on May 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power supply was cut


you can buy a new power cord or you can use another wire to replace the cord. just buy the same size then you will need to remove the rear cover to access the internal. and then the old cord must be removed from the ac terminal pin and the assembled wire with plug that you buy can be replaced. you can directly re soldered the end of the ac wire at the pcb for ac supply.

Aug 16, 2012 | Mitsubishi WD-57732 Projection Television

1 Answer

Screen went blank while still on. unplugged power cord and when I plugged it back in the power on light went green. Problem remains


Resolution:

Follow the steps below to troubleshoot this issue.


Verify that the AC power cord is connected securely to a working wall outlet.
Unplug the power cord of the television from the AC outlet.
Let the television remain without power for 1 minute.
Plug the power cord back into the AC outlet.
Attempt to turn on the television.
NOTES:

If the issue is still unresolved after completing all of the troubleshooting steps, service will be required.
Make a note of the STANDBY or TIMER flash pattern when referring the television to service.

Aug 13, 2008 | Projection Televisions

1 Answer

What can I use to clean my t.v. screen?


Unplug the AC power cord connected to TV set from AC power outlet before cleaning. Wipe gently with a soft cloth. If dust is persistent wipe with a soft cloth slightly moistened with clean water. If it does not help and dust still persists then use soft cloth moistened with mild detergent solution. NEVER USE AN TYPE OF ABRASIVE PAD, ALKALINE/ACID CLEANER, SCOURING POWDER OR ALCOHOL

Mar 15, 2010 | Projection Televisions

1 Answer

Will not power up


If youre not getting a power light then its most likely the AC main filter board ( Where power cords plugs into ) or if you do get a power light the deflection board needs replacement.

Dec 11, 2009 | RCA D52W19 52" Rear Projection Television

1 Answer

I have a philips 60pp9363 60in that worked beautiful for four years now it just wont power up period. No sound,no picture, no power light, no nothing. and it worked perfect yesterday.


The place to begin is with the fuse----with the set unplugged follow the power cord into the set---there is a fuse on the narrow right board--it can be checked--there are two on that board--one near the cord and another foward--you cannot just look at them--check them like any other fuse.

Sometimes a power surge or outage will take the AC fuse--it is the one right where the power cord comes in.

LET ME KNOW IF YOU NEED HELP OR HAVE ANY QUESTIONS.

sd tech

Oct 31, 2009 | Philips 60PP9363 60" Rear Projection...

2 Answers

I have a Hisense tl 2020 and last night when turned it on I had no sound


Try first leaving the unit unplugged from main for one hour.

This will drain power and reset circuits.

Check also eventual cable connections, receiver box or device connected.

If that does not solve the problem, then there is an internal fault, probably on audio circuits or I/O board.

May 21, 2009 | Projection Televisions

1 Answer

No power to tv when i plug it in. don't know if all the way dead way to check it?


I really need the make and model number to help you.

My understanding of what you have said is that there is no standby light and no clicking sounds when you power on your unit. If this is true regardless of what type of tv it is there is a fair chance that the main ac line fuse is blown.

To determine if the line fuse is blown, remove the rear cover panel and follow the ac power cord to where it connects to the circuit board. The ac fuse is a small glass cylinder, about a half inch long. Replace the fuse with the same amperage and ignore the voltage rating. If the new fuse blows as well, your looking at involved circuit work which should be referred to an experienced repair technician.

Apr 29, 2009 | Projection Televisions

1 Answer

I need a new remote for my televison modle #TL2020 can you help me


try www.replacementremotes.com they should have the remote you need. Just enter the model number of your set in the search box on the home page of thier site.

Apr 07, 2008 | Projection Televisions

1 Answer

Compatible hisense tl2020 to program a remote control


CALL TIVO SUPPORT TO SEE IF THEY SUPPORT THAT MODEL IF THEY DO THEN THEY SHOULD GIVE YOU A CODE

TiVo Customer Support
Live agent support available: Monday - Sunday
7:00 AM - 8:00 PM Pacific
Phone number: 877-367-8486

Mar 24, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

61292 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...