Question about Mitsubishi WD-52525 52" Rear Projection HDTV

1 Answer

Red lamp light with newbulb, won't come on error code 34

How do you check the ballast wd 52525 mitsubishi DLP

Posted by on

  • jack_phenom Jul 17, 2008

    I have the same thing. Tv first had a very scrambled picture, then shut off by itself with red lamp light. Replaced lamp, but tv still won't show picture or menu. When holding menu and device together on the front, the blinking lights indicate error 34. Any suggestions?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 8,617 Answers

There are two 1000uf 16V capacitors on the PWB that cause that problem code 34 lamp abnormality. If you need more info let me know.

Posted on May 04, 2008

  • Alicia Breckel
    Alicia Breckel Mar 13, 2015

    The power board is the small board in the top left correct on the light engine assembly

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can i get a color wheel replacement for my DLP Mitsubishi WD-52525 210719 TV? I have changed the lamp and still the TV goes to black and the status light goes on.


This DLP tv model don't have a colors wheel.U hear alot of clickings sound,when power turn on?The Ballast board it dead.This board,job to help projection lamp to ignite.Tries websites like Partstore.com,Ebay.com to buy the Ballast board for the replacement.

Oct 21, 2010 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Own a mitsubishi WD-52525 52 in. Rear Projection HD TV. Already been through the "blinking light of death" problem about 2 yrs. ago. Now have a steady red lamp light. Purchased new lamp, installed, and...


You have to take the TV apart. Pull the electrical chassis out and look for bad electrolytic caps on the boards. sounds like caps on the power supply board are bad. You can tell if they are bad by the fact that their tops are puffed up and they may or may not be leaking brown fluid. Compare them against the other caps on the boards and you will see how they have flat tops.

BUT before you take the TV apart you can check the error codes by pushing "menu" and "Device" at the same time and holding for about 10 seconds. The status light will blink two numbers. ex. one flash pause two flashes is 12 Error Code Probable Cause

12 No error detected
22 Recovery from momentary Reset
32 Lamp Cover open
33 Air Filter Cover open
34 Lamp abnormality
35 Chassis Fan failure
36 Exhaust (Back Cover) or Lamp Ballast Fan failure
37 Engine (DMD or Lamp) Fan failure
38 Excess Lamp Temperature
39 Excess DMD Temperature
41 Short Detected
44 DVI Cable (between Chassis and Engine) disconnected


or use the table below -

8566f47.jpg

You can buy replacement caps from Mouser electronics online

Sep 11, 2010 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Wd 52525 red lamp light on but new lamp isn't


HI. the actual issue will be a failed ballast device. replacing this damaged power regulator will fix this issue. you can order your new ballast by clicking the link below.

Ballast(Click here to order)

Sep 02, 2009 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Buzzing noise from Mitsubishi DLP WD-52327 after replacing bulb


Did your replace lamp come on the screen or did you lose picture? Just because the LED indicator suggest replace lamp it doesn't mean it needs it. If your pix was dull or loss of brightness then replace it, if not then just reset your lamp timer, check your owners manual for instructions.

Feb 14, 2009 | Mitsubishi WD-52327 52" Rear Projection...

1 Answer

Mitsubishi WD 52525 lamp replaced, no picture, red light


You have to take the TV apart. Pull the electrical chassis out and look for bad electrolytic caps on the boards. The red LED probably means the 2 - 3300UF caps on the power supply board are bad. You can tell if they are bad by the fact that their tops are puffed up and they may or may not be leaking brown fluid. Compare them against the other caps on the boards and you will see how they have flat tops.

BUT before you take the TV apart you can check the error codes by pushing "menu" and "Device" at the same time and holding for about 10 seconds. The status light will blink two numbers. ex. one flash pause two flashes is 12 Error Code Probable Cause

12 No error detected
22 Recovery from momentary Reset
32 Lamp Cover open
33 Air Filter Cover open
34 Lamp abnormality
35 Chassis Fan failure
36 Exhaust (Back Cover) or Lamp Ballast Fan failure
37 Engine (DMD or Lamp) Fan failure
38 Excess Lamp Temperature
39 Excess DMD Temperature
41 Short Detected
44 DVI Cable (between Chassis and Engine) disconnected


or use this table -

8566f47.jpg

You can buy replacement caps from Mouser electronics online. There are plenty of solutions detailing how to do this already posted.

Jan 09, 2009 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

WD-52525 Red lamp Indicator


usually with that model when you get a 34 eror code for lamp abnormality, its directly related to the capacitors on the Power Pwb. You can get the V26 Power PWB repair kit at the following link which repairs that issue. It contains the replacement High temp capacitors with the board location numbers and PWB identification as well as the service manual on CD. Heres the link its under their repair kit ctegory.
http://servicemanuals.vstore.ca/

Sep 04, 2008 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Wd 52525 error code 34 lamp abnomality


the capictor problem is mostly for WS models
you can locate the dm model from this link
http://www.fixya.com/howto/h159332-mitsubishi_dm_board_repair
Here's something that might also be useful. After you turn on the set, and get the regular red blinky lights, hold down the Device and Menu buttons together for about 5 seconds.
The Power light will start to flash in a two digit sequence.

For example, 3 flashes, then 7 flashes = 37.


Here are the error codes, and the corresponding problem:

12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filter cover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cable between FMT and Engine disconnected

Jan 18, 2008 | Mitsubishi WD-52525 52" Rear Projection...

2 Answers

WD-52525-Code 34-Sound OK-No picture!


I had another problem kinda the same and emailed ctechnicians.com and they gave the fix.

Nov 02, 2007 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

WD-52525 New lamp-Code 34-Lamp abnormality?


check that you did not bend you connections on the lamp housing
when you reinstalled have seem this happen

Nov 02, 2007 | Mitsubishi WD-52525 52" Rear Projection...

Not finding what you are looking for?
Mitsubishi WD-52525 52" Rear Projection HDTV Logo

1,040 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1207 Answers

The Knight
The Knight

Level 3 Expert

72640 Answers

Jaime Hernandez

Level 3 Expert

2296 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...