Question about Canon PIXMA MP190 All-In-One InkJet Printer

Open Question

My CANON MP198 Printer can't detect ink-catridge. It says ink catridge can't recognized the catridige

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: printer will not recognize new blk ink cartridge.

1) Please do not use RE-FILLED cartridges as they will clog the heads terribly.
2) Turn off printer, Remove all cartridges, Gently move the printer head to the RIGHT with short thrusts. It is not necessary to move it completely to the right hand home position just simply away from the obvious jam.
3) With a flashlight and tweezers try to locate paper jam in the print head track. Best to also blow out paper chafe with a weak air bulb. WARNING: Do not let your male friend or relative use extremely strong air pump for tires or air blower at corner gasoline station. (Do not purchase the cheapest paper the future)
4) Unplug the printer to allow it to completely re-initialize the internal electronics..... about 10 minutes should be fine.
5) Replace all cartridges.
6) Power up printer, then re-boot your computer with the activated printer connected, then print a test page. Everything should be fine.

Posted on May 17, 2009

Ad
  • 84 Answers

SOURCE: printer will not recognize new blk ink cartridge.

I think either the printer's scanner(or film as some call it) and/or the carriage is faulty. The signal cable that connects the carriage to the logic board could also be a suspect. Try replacing these items one after another and the culprit will be isolated. Good luck.

Posted on Jun 03, 2009

Andrew Tung
  • 1 Answer

SOURCE: printer error

How to bypass the Alarm for Cano pixma MP198

Posted on Jun 15, 2009

komguy
  • 2306 Answers

SOURCE: have problem with my printer canon pixma mp198,

Some have posted reset instructions here, but I wouldn't do that since the ink can overflow and make a mess. You should have the absorbers replaced by a repair shop and the reset done properly.

Posted on Aug 03, 2009

cene765
  • 787 Answers

SOURCE: canon ip1880 catridges cannot be recognized

Do you try to replace the cartridges? Try it, it will help, believe me!!

Posted on Nov 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Canon pixma ip1300 cant detect ink cartridges


remove all the cartridges. using tissue or cotton cloth.. dub the connectors to the cartridge of the printer.. then wipe the cartridge connector area dry. if this does not work, you need new cartridges. with new cartridges and the same problem persist, your printer has the problem on the in decoder strip. area. hope to be of help.

Feb 14, 2014 | Canon PIXMA iP1300 Printer

1 Answer

Hi, my Canon MP198 cannot recognized the color cartridge. However, i only need to print in black and white.What should i do to solve this problem


In most cases the printer driver software can have errors while being in use or is shut down. So to reset remove your printer from the PC and uninstall the printer software. Now reinstall the printer software and then connect the Printer to be detected as a new hardware as it will be installed. Now check the printer properties to see the ink levels.
Activate head cleaning before a test is taken . Sometimes it is possible that the head is not reacting to the need of the PC command or can be an issue with ink drying or
poor ink cartridge contacts.

Jun 14, 2011 | Canon PIXMA MP190 All-In-One InkJet...

1 Answer

In canon printer mx 330 ink catridge cannot recognized u051


In most cases the printer driver software can have errors while being in use or is shut down. So to reset remove your printer from the PC and uninstall the printer software. Now reinstall the printer software and then connect the Printer to be detected as a new hardware as it will be installed. Now check the printer properties to see the ink levels.
Activate head cleaning before a test is taken . Sometimes it is possible that the head is not reacting to the need of the PC command or can be an issue with ink drying or
poor ink cartridge contacts.

May 20, 2011 | Office Equipment & Supplies

2 Answers

Ink cartridge not properly installed


I have gone through all the forums but none of them worked...

The correct solution for the problem is the canon printer needs to have both the color and black catridges present in the printer...
So even if you purchased new black catridge only you need to have the old color catridge to be placed in the place of color catridge....

So it will detect the catridges and if any of the one is empty it asks to select black at the time of printing and simply select it you will get a black print...

So make sure both the catridges either empty or full need to be placed to detect the catridges....

I hope it will be helpful.....

Feb 18, 2011 | Canon PIXMA iP1300 Printer

1 Answer

I bought a tesco refilled ink cartridge for my mp460 printer.but the printer doesnt rcognise the ink.please help me


in canon pixma printer it is not detect refill catridges so i advise you always use genuine catridge only.

Nov 20, 2009 | Canon PIXMA MP460 All-In-One InkJet...

1 Answer

After E4 display, cartridges will not move over to the left.


E4 says no ink, press the OK button to continue, and replace the ink.

Sep 15, 2009 | Canon PIXMA MP150 All-In-One InkJet...

3 Answers

Canon pixma mp 145 E4 problem


Dear Sir,

Error Code E4 = No ink.
Generally printer doesnt recognise refilled ink.
Try the to reset the ink catridges
by mp tool software,mptool reset the printers canon pixma series like MP150, MP160, MP170, MP180, MP450 and MP460.And there also facility to write and read EEPROM in the printer. Other excess this software is detect automatically installing printers in the computer.
Download Mp tool

i think it solves your problem,But the actual procedure and best solution is replace the ink catridges,according to canon new genuine canon ink catridges save your printer life also.
if you find any difficulty leave a feedback,we will glad to assist you


good luck

Sep 08, 2009 | Canon PIXMA MP160 All-In-One InkJet...

1 Answer

Catridge problem


when printing try to press resume button for about 5 seconds

Apr 06, 2009 | Canon PIXMA iP1800 InkJet Photo Printer

2 Answers

Canon pixma refill is not recognized


Dear nedaa,
You need to deactivate ink level detection function to keep your printer working after refilling the cartridge. Click here to know more how to deactivate ink level detection function.
Source:
Canon Inkjet Printer Forum
Canon Manual & Tools Dowload

Jan 17, 2009 | Epson Stylus 2200 InkJet Photo Printer

Not finding what you are looking for?
Canon PIXMA MP190 All-In-One InkJet Printer Logo

Related Topics:

310 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

2005 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...