Question about Projection Televisions

1 Answer

Lost the power cord for my 15" LCD tv model no:15mf400t/37

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 131 Answers

You could call a local tv shop they usually have extras. check radio shack or mcmelectronics www.mcmelectronics.com.

I use to get alot of call on cords and always had extra when people called.


I hope this helps thanks doctor video leadingedgeelecronics 1987

Posted on May 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

I have a Magnavox 15MF400T/37 LCD TV operating with a cabel connection. As of yesterday it has no functions but when I turn it on I get a message that says Attention No Signal. I have checked the cable...


Some of the newer TV's dont turn on if there is no input signal. Try a DVD player and see if that works. If it does, then the issue is most likely with the cable jack on the TV, which may need to be replaced..

Jul 21, 2008 | Projection Televisions

1 Answer

We have lost the power cord to plug into our Proscan TV model: PS52652 chassis: PTK169PDBS. where can we find a cord to purchase?


Check with techs that repair these sets or any tech. If they cant find the right power cord they can allways take the power cord from another name brand set and wire it in.

Aug 05, 2010 | Proscan PS52650 52" Rear Projection...

1 Answer

37 INCH LCD MAGNAVOX TV WILL NOT TURN ON. MUST BE


This problems,very common in LCD tv,after the tv was in used about a year or two.The new technalogy LCD tv don't handle heat very well,not like the old CRT Tube Tvs.The power supply board tend to have bad capacitors componnents leakage,that bulges up it top or puff up gases escape,that why it take times or couples pushes to the power botton to turn the tv on.U know basic electronic's,and have soldering tools and solders?Take the tv aparts,check for these bad capacitors,that bulges,puff up in the power supply board and replaced them,than ur power will work normal again.Or tries Websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.

Apr 29, 2010 | Philips Magnavox 51MP392H Rear Projection...

1 Answer

I have a Phillips LCD tv model #42PF7421D/37. and


I know on the plasma TV's it was a matter of updating or downloading and re-installing the firmware/software for the TV to fix the issue. Go to the following page and if the model you have is indeed a 42PF7421D/37 download the software on the page. Make sure you follow the installation instructions to update the software otherwise the set will become a 150 lb paper weight.

&scy=US&slg=AEN&sct=LCD_TV_SU&cat=TV_CA&grp=SOUND_AND_VISION_GR&session=20091111140139_64.85.227.44&ctn=42PF7421D/37&mid=Link_Software&hlt=Link_Software">Philips Support Page

Nov 11, 2009 | Projection Televisions

1 Answer

Drop my tv rip out the power cord philips tv model 20pt6341/37


hi i hope i can help you ? you said there is two bent pins on the main cicuit board can you please have a look do they say L N at the bottom of the pins? if yes this is where you reconnect. top tip where you had the tv pluged in and where the tv is normally this will give a good indication if that is where you put the L N.also please check the pins for any damage. like solder joints for safety.

May 01, 2009 | JVC AV-48WP30 48" Rear Projection...

1 Answer

Cant control volume with dish satelite remote


FIRSTLY
  • With the desired equipment on, press and release the Mode button until the light flashes behind the correct mode.
  • Using the tip of a pen or the eraser on a pencil, press the address button.
  • Enter the code (see links to find your code below) on the remote's numbered keypad for the equipment.
  • Press the Address button. If the code entered is valid for the remote, the mode light flashes three times.
  • To verify the code works, try several functions for that equipment. Some codes may provide partial functions or respond differently than the button's titled function. Try the other codes listed for that device until you find one that offers more complete functionality.
wHAT IS THE REMOTE MODEL?

Jan 21, 2009 | Philips 60PP9200D Television

1 Answer

Powering on my tv


Dear smmmobil,
The problem lies with the SMPS (switch mode power supply ) of your TV. The smps board needs to be replaced.

ramesh22

Jun 15, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...