Question about Apex Digital GB4308 43" Rear Projection EDTV-Ready Television

1 Answer

No picture I have sound but no picture. I have tried to use all the av's and there is no picture but there is sound to all of them. Any idea's?

Posted by on

  • 1 more comment 
  • Anonymous May 12, 2008

    YES I HAVE THE SAME PROBLEM BUT I ALSO HAVE A RED,BLUE,AND GREEN ARCH THATS GOES THREW MY BIG SCREEN AND I HAVEN'T DONE ANYTHING CAUSE I DON'T KNOW WHAT TO DO OR REPLACE OR LOOKING FOR

  • phickerson21 Jun 27, 2008

    have sound but no picture

  • Anonymous Nov 02, 2008

    I HAVE SOUND AND NO PICTURE AND I HEARD A POP NOISE BUT NO SMELL OR SMOKE CAME FROM IT

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Apex Digital Master
  • 8,617 Answers

Sounds like the vertical output IC is either defective or needs to be re-solderd

Posted on May 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When i connect my ps3 via the hdmi socket i get no picture, only sound when i use the ps3 controller. i have tried using the new scart lead and still nothing. i have gone through all the AV channels also....


You may have it set to scart video audio hdmi , instead of the scart try using the analogue video also , yellow connector on tv if it has it , also AV and scart aren't always the same on tvs search through the source option on the tv

Dec 01, 2014 | Sony SELECT KDF-E50A12U Rear Projection...

1 Answer

WD73927 sound cuts off but picture stays


try the soft reset this model should have with set on Menu,1,2,3 enter.

Nov 29, 2012 | Projection Televisions

1 Answer

Clicking on the power supply board(no picture or sound)


If you hear a buzzing, humming or rapid clicking noises this could be a problem with your ballast.Might be a good idea though to pull out your lamp just ensure its not damaged.You can find these at discount-merchant.com

Apr 01, 2010 | JVC AV-48P575 48" Rear Projection...

1 Answer

I have jvc av-56wp30 all of a sudden the red in the picture is doubled. any ideas what that could be?


That sounds like a convergence failure. The AV48WP30 convergence repair kit from www.tvrepairworld.com should solve the issue. The kit contains the components and the CD with instructions.

Dec 14, 2009 | JVC AV-56WP30 56" Rear Projection...

1 Answer

Jvc av-48wp74 i have sound but no picture History I have a JVC AV-48wp74 Projection tv when i got this tv the stk ic's were overheating and the picture would come and go typical of overheating . I put a...


Number 1- don't spin your wheels on the replacement board repair the old, it can't be unrepairable. As for the over heating of the conv ic's not normal. Since you changed the conv bd and they still over heat, if I had the set I would do a reset of the registers in the service convergence mode then re-center the grn then red then blue and that will be with the centering magnets and yoke on the crt's, If you don't have a template for that then you will have to make good old fashion geometry measurement's, the green is first, every line straight vert, horz, and spaced, with of coarse the cross in the middle will be dead ctr. The overheating problem can be because the register settings are advanced to far do to corrections thru out the years with comp's changing in value and us compensating with adjusting the convergence.

Feb 27, 2009 | JVC AV-48WP74 48" Rear Projection...

1 Answer

I have Hitachi CMT 2928FX, I am using AV input 1 on back, great sound, black and white picture that is just out of synch. I do not have the Hitachi remote, I am using the programable remote from DISH TV. I...


May be one of two things. With a standard av input (called Composite Video and usually colored Yellow) then the signal must be 480i, Standard Definition with (i)nterlace. If it is higher, say 1080i (another interlace signal but High Definition), 480p (Standard Definition in (p)rogressive mode), or 720p (another HD in progressive).

Try reseting the Dish receiver by unplugging it for 15 seconds.

Aug 18, 2008 | Hitachi Projection Televisions

4 Answers

No sound on JVC AV-48P575 48 inch rear projection TV


Try going into the menu and find something called, "center channel input." If it is on, the sound will not work. Turn it off, and the sound should be restored.

Mar 23, 2008 | JVC AV-48P575 48" Rear Projection...

1 Answer

Sound but no picture


You say AV4, is this the HD part? And if so, then have you checked the video board area?

Sep 12, 2007 | Philips 60PP9202 60" Rear Projection...

2 Answers

HAVE PICTURE BUT NO SOUND


check for center channel option in menu, change option and test

May 21, 2007 | JVC AV-56WP30 56" Rear Projection...

1 Answer

No av picture


I have the same problem. Any suggestions

Sep 02, 2006 | Philips 60P8342 60" Rear Projection...

Not finding what you are looking for?
Apex Digital GB4308 43" Rear Projection EDTV-Ready Television Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Apex Digital Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

Dave Naylor
Dave Naylor

Level 3 Expert

834 Answers

The Knight
The Knight

Level 3 Expert

68301 Answers

Are you an Apex Digital Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...