Question about D-Link DWL-G700AP 802.11g/b Wireless Access Point

2 Answers

Password setting not going

Hi

I have installed this D-link device and it is happily connecting me to internet from my VISTA laptop PC.

Now .. I want to set the password. I can not get any connection through http://192.168.0.50 to get the setup utility going.

How can I proceed.

Regards
George Burrell

Posted by on

  • majoo Jun 20, 2008

    I should set a password for my D-Link DWL-G700AP router

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 166 Answers

Hello there.

You need to give the correct IP address to connect to your router through your web browser. 192.168.0.50 is most likely your Vista PC's IP address, not the D-Link router.

To find out what IP address to type into the web browser please do the following:

1) Press the "Windows" key + "R" on the keyboard, at the same time.
2) Type "cmd" without quotes in the run box and click "ok"
3) Type "ipconfig" without quotes.

Notice it says Default Gateway followed by an IP address, this is your router's IP.

Hope this helps.

Posted on May 04, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 13,433 Answers

The address your are typeing is possibly wrong

hold down the windows key and press r.
in the run menu type in CMD

now in the shell windows type in ipconfig

ipconfig will show something like this
IPv4 Address. . . . . . . . . . . : 192.168.11.2
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.11.1

note the default gateway address that is the address you need to connect to

in my case its http://192.168.11.1 check yours

Posted on May 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Problem with D-Link 1360 n access point. Not able to visit ip address 192.168.0.50


The internal Wi-Fi radio is enabled by default on most new wireless routers.
However, if you purchased a D-Link router used, you may find that the internal radio is disabled because the previous owner had an exclusively wired network and wanted to eliminate the possibility of a hacker breaking into one of her computers.

Enable the Wi-Fi radio on your D-Link router to enable your computers to connect to the Internet wirelessly.

Connect the router to your computer using an Ethernet cable.
Open a web browser and browse the IP address "192.168.0.1."

Enter the username "admin" and leave the password blank.
Note that these are default values; both the user name and password can be changed.

Click the "Setup" tab at the top of the screen, then click the "Wireless Settings"
Scroll to the bottom of the screen and click the "Manual Wireless Network Setup" button.

Place a check in the box labeled "Enable Wireless" and click "Save Settings."
Click start control panel administration tools computer management device manager scroll to network adapters should see a yellow question ? exclamationmark! or a red Xright click install drivers.

The driver might be on the disc supplied by your ISP internet service provider
or the motherboard disc
If you cant install the driver
Make sure you Ethernet/internet is enabled in biosrestart your computer during the boot up process you will see on your screen a certain key to
press to enter set up (BIOS) press and hold that key to enter bios using arrow keys navigateto integrated peripheralslook for SiS On Chip Pci Device press enter scroll to SiS 10/100m press enter make sure its
"Enabled"ima

D-Link Wireless Router

D-Link routers use the connection from your Internet service provider to create a wireless network for the various Wi-Fi- enabled devices in your home or office.

Once the router is installed, you can truly enjoy the portable capabilities of your laptop or other wireless device.

D-Link routers have a straightforward installation process, despite the advanced technology behind wireless equipment. So there is no reason to wait around for a technician to help you install your wireless equipment. Remove the cable that is attached to the "Internet" port on the rear of your DSL or cable modem.

Plug the Ethernet cable into the "Internet" port on the modem and plug the other end of the cable into the "Internet" port on the rear of the D-Link router. Attach the power adapter to the port on the rear of the router and plug the adapter's cord into a outlet.

Remove the power cord from your modem and wait 10 seconds before plugging it back in.
This will reinitialize your modem and force it to establish a connection to the D-Link router.

Your router will immediately begin distributing a wireless network with the "D-Link" network name.

Connect your computer to one of Ethernet ports on the rear of the router and open a Web browser.

Type "http://192.168.0.1" into the address bar and press "Enter." Enter "admin" into the username field and type "admin" again into the password field.

Click "OK" to open the wireless configuration page. Click "Wireless Security Setup Wizard" to create a wireless password for your router's network.

Click "Apply" to save the changes to the router's settings.
Network D-Link wireless

Type the router IP address, "192.168.0.1", into your Internet browser. Press "Enter" on your keyboard.

Enter your username and password to log into the D-link configuration panel.
By default, the username is "Admin" with a blank password field.

To prevent outsiders from being able to access your D-link router's configuration panel, change the username and password to something more secure.

This can be done by selecting "Tools" from the menu and selecting "Admin."
Select "Administration Settings" and enter your new username and password.

Save your changes by clicking "Apply."
Enter the IP addresses for the computers you want to give access to your router.

You can do this by clicking the "DHCP" link underneath the "Home" tab.
Click "Apply" to save the IP addresses.

Select the "Wireless" link underneath the "Home" tab.
Enter a name in the "SSID" field to identify your wireless network.

Choose "WPA" for your "Security" option.
WPA will provide the highest level of security for your wireless network.

Create a WPA password to access your wireless network.
For maximum security, enter a combination of numbers, letters, and symbols.

Store your password in a safe place in case you ever forget it.
Click "Apply" to save your settings.

Install a software firewall program on your computer to add an additional measure of security for your wireless network.

A few of the popular firewall programs available are Norton Antivirus, McAfee and Zone Alarm.

Mar 18, 2014 | D-Link Wireless N Access Point Dap-1360 -...

2 Answers

I can't set the bsnl access point in lg gs 190?


Have you send sms to BSNL for setting up your phone?

First sms: you have to type "GPRSPRE" in the sms and send it to 53733.

Second SMS: Again you have to type mobile company name and model no. and send it to 58355
for example "SAMSUNG B3133" as text in the sms and send it to 58355.

Then you will receive the APN settings. Then you ma or may not be able to use internet in you mobile and in laptop through it.

If you can use internet in the mobile (stand alone) then attach it to laptop/desktop. Samsung device driver will be installed automatically. and you will see your mobile is detected as a modem in the phone & modem section in the control panel.

Then create a normal dialup connection in your network section. Then dial it. you will be able to connec to internet.

Feb 25, 2011 | Wireless Access Points

1 Answer

Cingular WAP settings


Hi..i am providing you with the WAP and other settings,but still if you need any help,then please contact Cingular at 866.CINGULAR(866-246-4852)

For CSD (Wireless Internet)
Function Setting
Settings Name: Cingular Wireless Internet
Home Page: http://device:home or http://device.home
Session Mode: Permanent
Connection Security: On
Dial-up Number: 14152441012
Gateway IP Address: 66.209.11.61
Authentication Type: Secure
Dial Type: ISDN (on network)
Analogue (off network)
Login Type: Automatic
User Name: WAP@CINGULAR.COM
(All upper case)
Password: CINGULAR1
(All upper case)

For GPRS (Wireless Internet Express)
Function Setting
Settings Name: Cingular Wireless Internet Express
Home Page: http://device:home or http://device.home
Session Mode: Permanent
Connection Security: On
APN: wap.cingular (lower case)
PDP_Type: IP
Gateway IP Address: 66.209.11.61
Authentication Type: Secure
Login Type: Automatic
User Name: WAP@CINGULARGPRS.COM
(All upper case)
Password: CINGULAR1
(All upper case)

Now to set up MMS (Multimedia Services)
Name: MMS
Homepage: http://mmsc.cingular.com
Gateway IP 1: 66.209.11.61
Port 1: 9201
Domain 1: (blank)
Service type 1: WAP
Gateway IP 2: (leave alone)
Port 2: 9201
Domain 2: (blank)
Service type 2: WAP
DNS 1: (leave alone)
DNS 2: (leave alone)
Timeout: 10 minutes
CSD No.1 14152441012
Username 1: WAP@CINGULAR.COM
password: CINGULAR1
Speed(bps): 9600
Line type 1: ISDN
CSD No.2: (blank)
User Name 2: (blank)
Password 2: (blank)
Speed(bps)2: 9600
Line type 2: ISDN
GPRS APN: wap@cingular
Username: WAP@CINGULARGPRS.COM
Password: CINGULAR1

Good luck :-)

Apr 22, 2010 | Wireless Access Points

1 Answer

Cannot go to 192.168.0.50 again after receiving internet connect


I would recommend going to the D-Link website, checking for a new version of firmware, and then upgrading. Set the device back to factory defaults, and rebuild the configuration from scratch afterward. That should resolve the issue.

Nov 21, 2009 | D-Link AirPlus Xtreme G DWL-2000AP...

1 Answer

Forgot Network Security Key


ok at first you go to their device page connect the device to the pc or laptop then open the internet explorer in the address bar type 192.168.1.1 or 2.1 or 0.1 try it then asking to you
user name and password just type in the user name admin and password is admin or password

go to the wireless option in that security option is there just get it

Apr 05, 2009 | Apple AirPort Extreme Base Station

1 Answer

Can't connect to configure password through web address 192.168.0.50


When you reset the AP, how long did you press the reset button? To reset the AP to factory defaults, the reset button should be pressed and held for at least 15 seconds. Also, once reset, the AP should have the following settings:

IP address: 192.168.0.50
Subnet Mask: 255.255.255.0
Default admin username: admin
Default admin password: <blank>

When connecting your PC, either set an IP address within the same subnet (192.168.0.51 255.255.255.0) or choose "Obtain address automatically".

I hope this helps.

Dave Grannas

Jan 25, 2009 | D-Link AirPremier DWL-8200AP 802.11a,...

1 Answer

Fifth computer unable to connect to internet


-- ckeck if you see 'wireless connection' in the network connections, in order to find it, click start --> control panel --> network connections and you must see wireless connection in case of win xp..

start --> control panel --> network and internet --> network and sharing center --> manage network connections and you must wireless network connection under LAN or hi speed connection... in case of win vista 

--if you have that ikon that means you have your drivers installed on the computer properly 
--right click wireless network connection and click "view available connections" in case of  xp and "connect/disconnect" in case of vista you must find the network and get connected..
letme know if you have problems connecting..

Jan 24, 2009 | 2wire Wireless-G 802.11g ADSL Gateway

2 Answers

Belkin wireless adapter g usb


WPA is safer as all in all it's a lot harder to crack due to being a lot more characters in the passkey. The easiest thing to do would be explain how i have mine set up. And you could compare the 2.. As i have XP Desktop & Vista aswell. So your Laptop connects ok now but is still an unsecure network.. On your Dektop. When you try to connect. Are you entering the 26 character key on the bottom of the livebox?

The main thing to realise with the Livebox is everything is reversible.. And to not worry about changing something..

So let's get this started, When you open up the " Connect To A Network " you can see your Livebox-XXXX. Next to that does it say "Unsecured Connection"? If this is the case then your Livebox is still not properly configured.. What i would recommend doing is starting a fresh with the Livebox, and i explain how to set it all up from Default. icon_smile.gif

IF you don't remember your internet login details then go to "Configuration.adsl" and click My Services then Internet. Your info will be in there. Hopefully you remember your password.. icon_smile.gif

If you don't know how to do a reset of your liveox. Press and hold the "1" button on the back of your livebox. Unplug it from the mains whilst still holding the "1" for 10 seconds. Then plug it back in. [ still holding the "1" ] The lights will flash a bit and after a minute or two it will go back to normal.

Go back to "configuration.adsl"
Username: Admin
Password: Password

If i start from the top section and work down it should make it easier to follow:
My Services>Internet>Connection Parameters Filled In..
Phone Over ADSL> Nothing needs changing
Digital TV> Nothing Needs Changing.
Liveprinter> Nothing Needs Changing.
Submit

Security> Associated Devices> Will Be Empty
Firewall> Medium
Wireless Connection> Channel Number> 11
Security Key(WPA-TKIP)> Same As What's On Bottom Of Livebox.
Enable Wireless Lan> Ticked.
Submit

Configuration> Update> v5.10.7-uk
Administrator> Change the password while you're there..
Submit

Advanced> Wireless> Pairing Time> 10 minutes should be fine.
Your Livebox name can be left as it is.
WPA Security Only
Wi-Fi Easy Pairing.. Might aswell leave it on..
Submit

Now if we set up your laptop first.
Go into Connect To A Network. Your Livebox should be there. It also SHOULD say Secured Network. If there is a Red Cross then you will need to do what i suggested yesterday on my previous post.

Go back to connect.. Enter the 26 char. passkey with caps lock on.. And you should be connected no problem.

Now for the Desktop.

when you log on.. In the taskbar in the bottom right should be something to do with wireless networks. Double click this.. If it mentions something about using the software that came with the device.. Then use the software.. If not then windowsXP will show your network. Double click it.. Enter the same 26 character code.. And you SHOULD be connected.

Let me know if that works.. Sorry for the really long post, but detail is something i do quite well... icon_smile.gif

May 26, 2008 | Wireless Access Points

2 Answers

Windows vista


I had a friend that had this same problem.

As long as you know the password to the administrator account log into that and give your account administrator rights and you should be able to access the internet afterwards. I'm not sure exactly how this is done if it works like XP did then you will need to boot in safe mode by usually hitting f8 during the initial booting up of your computer.

Jan 23, 2008 | Arris SURFboard SBG900 802.11g/b...

5 Answers

Vista compatibility


Vista has very little drivers for equipment sad but true. However in your case you can use Airport Extream. However here is what an apple tech had to say: If you are a Vista user and you don't have access to a Mac, you will not be able to get this working. Apple hasn't yet stirred itself to release a version of Airport Express Assistant that works with Windows Vista - you can't set it up via Windows' own networking software and nor does the Airport Admin Utility work under Vista. It installs and you can run it, but it returns error messages if you try and connect to the Airport Express. I had to use a Mac to get it working, though once it's set up as a client to your existing wireless network, you can stream from iTunes on a Vista PC to the Airport Express. The documentation is very poor, too, with this: I had to do extensive Googling first to track down the fact that I couldn't set it up with Vista and second to identify the device's IP address and default password. Having said that, it is a breeze to set up via a Mac and works like a dream witih Vista once it's up and running. But don't bother if you have Vista until Apple updates the software. Was this review helpful to you?

Aug 23, 2007 | Apple AirPort Express (M9470Z/A) 802.11g/b...

Not finding what you are looking for?
D-Link DWL-G700AP 802.11g/b Wireless Access Point Logo

Related Topics:

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Wireless Access Points Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

scramblepad
scramblepad

Level 2 Expert

66 Answers

Anthony Chiang
Anthony Chiang

Level 3 Expert

524 Answers

Are you a D-Link Wireless Access Point Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...