Question about Whirlpool Duet GHW9150P Front Load Washer

2 Answers

FRONT BELLOWS EMAIL SHEAFIVE@VERIZON.NET THANKS

Posted by on

2 Answers

Try holding the signal button for 5 sec

Posted on May 13, 2008

I have a whirlpool duet washer i can't retrieve the model number because the door is locked but the dryer which is the match to the washer is model number GEW9200LW. My question is that when I hit the control button then start, a muttled beep will sound not allowing the door to open. I get an error message of DL then it flashes to F? Any help?

Posted on May 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was pushing a bulky item into the washer and a spring came loose from around the gasket. where does it go?


If it is the bellows spring thats what holds the big rubber piece( bellows) to the front of the washer. Make sure bellows it fitted in place over front of machine..pull spring over rubber edge at front..If you never did it before have someone help you Good luck...please vote if i helped you thanks

Feb 02, 2011 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

FTF2140ES0 Bellows Kit replacement


remove and install a new bellows kit for a Fridgidaire front-loading washer model ftf2140es0

Nov 09, 2009 | Frigidaire FTF2140E 3.5 Cu. Ft. Front...

1 Answer

Door won't lock shut


Removing the door safety switch:
1. Disconnect the washer from the electrical supply.
2. Release the bellows from the front panel:

Releasing the bellows (door boot) from the front panel:
The front of the bellows is installed over the lip of the door opening in the front panel and held in place by a spring loaded wire loop.

3. Open the loading door.
4. Using needle nose pliers, start where the spring and wire are connected at the bottom of the bellows and pull the wire out of the groove of the bellows.
5. Pull the bellows off of the lip of the front panel.

6. Remove the (2) screw holding the switch assembly to the front panel.
7. Pull the switch assembly into the door opening and unplug the electrical connectors.

Install is the reverse of removal.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jul 30, 2009 | Kenmore Washing Machines

2 Answers

How to replace the door bellows seal ?


Unfortunately the service manual will not tell you how to replace the bellows.

Tilt the machine back to create more space between the front on the door and the outer drum. Remove the screws for the kickplate and remove the kickplate for easier access. Open the door and remove the spring clamp holding the bellows to the door opening lip. Push the bellows into the drum to get access to the outside/ rear of the bellows (where it connects to the drum). There you will find another clamp which you loosen/ remove with a socket. Some models have an overfill tube on the top of the bellows (remove it from the bellows). At this point you should be able to completely remove the bellows.

Align the new bellows to the outer tub. Attach and tighten the inner clamp (be careful not to over tighten and periodically check the bellows and clamp placement as you're tightening to make sure it doesn't slip off). Attach the overfill tube (if equipped). Lay the machine back to level and install the front of the bellows to the door opening lip. Re-install the spring clamp by starting at the top and working your way down both sides (may be easier with 2 pairs of hands). Be careful not to overstretch the spring on the clamp.

Test with a quick fill and let it agitate for a few minutes to ensure there are no leaks (be ready to hit cancel and have a few towels just in case it leaks). Re-install the kickplate, make sure machine is still leveled correctly by trying to rock it diagonally from the top. Enjoy clean clothes!

Dec 19, 2008 | Whirlpool GHW9100L Front Load Washer

2 Answers

Replacing bellows on Whirlpool Duet HT model GHW9400PL0


I have not seen a tech sheet (or service manual) that details how to remove one of these. Basically, once you have your replacement boot (availible at local parts stoares or from the manufactures web site on line), You can follow these steps:
1 - Remove the front clamp. (a silver peice of wire with a spring at the botom) A small flat head screwdriver will let you pull it off.
2 - You will have a clamp on a hose that comes from the dispenser to the boot on some models that you will have to disconnect.
3 - There is a second clamp on the tub side itself. Remove it by using a short phillips head screw driver to unscrew it.
4 - remove the boot
5 - Reverse the procedure making sure to line the new boot up at the top. (there is a arrow that needs to be ligned up on the tub and the boot.
Taking the lower front panel off can give you a bit more room to work. You can take it off by removing the screws at it's bottom.

Jun 14, 2008 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Door Bellows


ben it is very complex to replace

May 07, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Duet bellows gasket manuel


I dont have a link but I have the full service manual in PDF format please post your email and I will send it to you

Apr 24, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Torn bellows


When you get the bellows repair kit for your model, it should have the instructions and all the necessary parts for replacement.
You may need to use some muscle to replace it and may take 1 to 2 hours to complete. If you have trouble finding the part or if there are not sufficient instructions included, then email  back! ok?

Feb 07, 2008 | Kenmore Elite 45986 Front Load Washer

16 Answers

How to replace the door bellows seal ?


I need some one to tell me how to install the rubber seal on a bosch maxx Eurowasher front loader washing machine. Part of the seal ripped off so water leaks out. Its only 6 months old and its not covered by warranty.

Jan 24, 2008 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...