Question about Stanley Bostitch 18 Gauge Brad Nailer 1 - 1/4IN - BT125K - 2

1 Answer

Can I use GA 16 in a Bostitch 18 GA? - Stanley Bostitch 18 Gauge Brad Nailer 1 - 1/4IN - BT125K - 2

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 262 Answers

No you cannot. The 16 guage will jam in the gun or two will come out at a time.

Posted on Aug 21, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Bostitch troubleshooting


Are you using 18 gauge or 16 gauge nails?

Aug 17, 2014 | Stanley Bostitch FN16250K - 2 16 - Gauge...

1 Answer

What is the strength of a joist hangar for a 2by 8? It has six nails straight in the face board and four through the joist at an angle.


If the hanger has an LUS it's 18 gauge. If it has LU it's 20 ga. for light loads,ceiling joists.For floor joists you should use HU 14 Ga.,or HUS 16 Ga. These # come out of Simpson strong -tie book. -

Aug 07, 2011 | Garden

1 Answer

I inherited a Bosch T31 bradder and stapler. Couldn't get any help at Home Depot chosinga nails. Bought Porter Cable 16 Ga. 1" finish nails (PFN16100-1). Released arm and slid the nail carrier...


BOSTITCH T31-1 stapler & T31-2 STAPLER and NAILER. Both use 18 gauge (very fine gauge wire). Try using 18 gauge Bostitch staples (used in BT model bostitch staplers). Good Luck

Feb 03, 2011 | Stanley Bostitch N80CB Coil Framing Nailer

1 Answer

Bostitch bt50b makes a plop sound but driver does not come down


This most often happens because of a leak in one or more of the O-rings or a lack of lubrication. The plunger is not in the proper position and doesnot have enough power to move the plunger or the plunger assy moves only enough to clear the relief valve for reset. In any case, the unit shouldbe taken apart, cleaned and relubed. This may be enough to resolve the problem. I would change the O-rings at the same time and be sure to lubricate them.

See the link below for additional information and a link to a diagram site.

Dan

Link: http://www.fixya.com/support/t6558387-just_lately_bostich_coil

Nov 03, 2010 | Stanley Bostitch Bt50b 18 Ga Brad Nailer...

1 Answer

I have a central pneumatic 16 ga. nailer how do I get parts !!!


Central Pneumatic is a Harbor Freight brand, if parts are available for that item it would be though them. http://www.harborfreight.com/contact-customer-service Hopefully they can get you what you need. If not unfortunatly that nailer will be a throw-away. If you need to replace this nailer I would recommend spending the extra money and buying a name brand nailer like Porter-Cable or Bostitch, besides both being reputable brands, they offer factory service, parts and rebuild kits for their nailers.

Oct 09, 2010 | Air Tools & Compressors

1 Answer

18 ga. Bostitch nailer that has a small brad jammed in it.


check your hex wrenches they could be standard when they need to be metric.

Sep 23, 2009 | Stanley Bostitch 18 Gauge Brad Nailer 1 -...

1 Answer

Bostitch nail gun loss of pressure, won't fire nail


Hello. I can help you. The nail gun you have uses 18 gauge brads. I would use only original Bostitch 18 gauge.

The one MM of difference you mention is the reason why you do not have the pressure you did have. Get rid of those 31MM brads and get the 18 gauge. Home Depot carries the Bostitch line. I would go there or to homedepot.com

May 20, 2009 | Stanley Bostitch BT200K

1 Answer

Craftsman 16 guage finish nailer. shoots 2 nails at a time. what


wrong gauge nails or wrong head type nails check that the magazine is not loose

Jan 09, 2009 | Stanley Bostitch 18 Gauge Brad Nailer 1 -...

Not finding what you are looking for?
Stanley Bostitch 18 Gauge Brad Nailer 1 - 1/4IN - BT125K - 2 Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Tools & Hardware - Others Experts

John Trevino

Level 3 Expert

1388 Answers

yoopertech

Level 2 Expert

131 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Stanley Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...