Question about Sony STR-DG510 Receiver

1 Answer

Code for sony receiver model str d565 protect mode

Hi. I have an older sony receiver model str d565 and i need the code because it's in protect mode. Can you help?

Posted by on

  • 1 more comment 
  • Anonymous May 27, 2008

    i have an sony receiver model str d 565 and i need tha code because its in protect mode

  • tway67 Aug 25, 2008

    I dont Know If my Sony d565 is in protect mode or not ? but I replaced the fuse and it still wont work . It only has two orange lights light up and they are dimm ? so does that mean protect mode or what ?

  • Anonymous Mar 14, 2014

    stays in protect mode then turns off

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

If you need support you can log into:
http://esupport.sony.com/US/perl/support-contacts.pl?mdl=STRDG510

for free tech support on sony chat line

Posted on Jun 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why is it blinking protect?


Try disconnecting all the speakers and turn it on if it still goes into protect you will need to get it serviced but if it turns on then you have a problem with the speaker or wire run (check for shorts )

Roger

Jan 07, 2016 | Sony Str-d565 Digital Audio Video Control...

1 Answer

Protect mode


I didn't see any mention of it in the STR-D565 manual, but on many other Sony models the "Protect" indicates a short in a speaker wire.

Aug 22, 2013 | Sony STR-D565 Receiver

1 Answer

Why do speakers crackle and flash protect


Check your speaker wires. Make sure they are not touching each outher or back of the unit. This will overload your output transistors and shut down your amp.

Aug 13, 2012 | Sony Str-d565 Digital Audio Video Control...

1 Answer

Hi. my sony STR-DE 597 go in protect mode. how can I fix/repair this? Give me a tips.


protect mode means there is a shorted components inside your reciever it's probably the out put transistors take out the transistors and test it with a multimeter.

Jul 11, 2011 | Sony STR-DE597 Receiver

1 Answer

I have rewired my receiver and the SOny str-d565 keeps shutting off. Is this fixable or should I just get a new receiver?


This unit most likely has shorted output transistors. The unit is entering protect mode which will prevent further damage to the unit. Expect a parts cost in the $40 range for this repair.

Dan

Feb 11, 2011 | Sony STR-D565 Receiver

1 Answer

I still have a Sony STR-D565 Receiver - but there's one major problem. After a variabel time in use it stop working. If I push the ON / OFF button , It gives the receiver new life, but just for a while....


If the word "Protection" is not flash in the display when this happens, then the receiver is in a tight area where it can't get enough air and is over heating. There are temp senosors on the heat sinks where the output transistors are mounted, and they will shut down the power supply in an overheat situartion, but the protecting indicator shold flash. Blow some air over the receiver and see if that stops the problem.

Aug 30, 2010 | Sony STR-D565 Receiver

1 Answer

I turn it on and it says protect and wont play.


That model of receiver goes into protect mode when there is really
low
resistance or a short on your speakers/wires. It does it to protect the
final drivers in your amp. Does it do the same thing with all of your
speakers disconnected? If it doesn't then you might have a problem with
one of your speakers or wires. Check your wires for shorts in them
first. That may be the only problem. That model is designed for 8 ohm
speakers, but you can go down two 6 ohms safely. I have a STR -D865 that

has been running 6 ohm speakers safely for almost 3 years now. A way to
check your speakers out is to take an ohm-meter across the terminals on
them(with the receiver unhooked). They should read anywhere between 8
and 4 ohms. Check with the manual on your speakers to see if they
correspond. If the resistance is really low, you may have a short in
that speaker. it is also possible that if they are 4 ohm speakers, you
could have damaged the drivers in your receiver. I know the model above
mine, (the 965) has a 4-8 ohm speaker selection switch on the back. The
lower models were not designed to run 4 ohm speakers. Hopefully this has

been of some help.

Brad

Jul 18, 2009 | Sony STR-D565 Receiver

1 Answer

I have a Sony STR-D565 Receiver. I bought new


I resently hooked up my sony std d 565 reciever for 5.1 speakers and I keep hearing beeping, what is wrong?

Apr 04, 2009 | Sony STR-D565 Receiver

1 Answer

Operating instructions for sony str-d565 receiver


this is a link just make sure to disable protected mode in internet explorer sometimes it has problems with links

http://www.docs.sony.com/release/STRD665.PDF

Feb 23, 2009 | Sony STR-D565 Receiver

1 Answer

MODEL STR-D565 PROTECT LIGHT FLASHING


Hello!
Your amps' output section is shorted and is sending it's supply voltage straight to the speakers. The protect circuit is there to protect your speakers from being burnt. You need to go to an authorized Sony service center. Good Luck!

barneyluc

Oct 11, 2008 | Sony Audio & Video Receivers

Not finding what you are looking for?
Sony STR-DG510 Receiver Logo

Related Topics:

2,094 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Audio & Video Receivers Experts

nexrad_chris

Level 2 Expert

117 Answers

Cindy Wells

Level 3 Expert

4756 Answers

Pieter Vleeshouwers

Level 3 Expert

1410 Answers

Are you a Sony Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...