Question about Car Amplifiers

1 Answer

I have 1998 dodge neon

I have a neon but when I have to stop at the light it sounds that it is going to give out on me it would shack on me?it is reading 12-45-55 & i don't know why it is like that.
thank;s
rdds@rogers.com

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,042 Answers

Bad timing, or maybe too loud of a car stereo for the alternator to support.

Posted on May 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hook up sound to a sony ps-lx340


try a RADIO SHACK SA-155 MINI AMP at Radio Shack. I believe around $30.00. Use the amp many times.

Nov 28, 2014 | Sony Ps-lx320 / Ps-lx340 Stereo Turntable...

1 Answer

I have a DA 1200.5 5 channel amp. It stopped


diconnect all your speakers from the amp and see if the light turns green. if it does, reconnect one speaker at a time to find out what speaker is making the amp go into protect mode

Feb 24, 2010 | Crunch BlackMaxx BLX2000D Car Audio...

1 Answer

I have an Alpine MrP-M500 that is not giving off sound. The light is diming, and blinking meaning it is in "safemode." ive done everything, new fuses, ground is good, wires are good, sub is good. I got it...


yes you have a internal fault of the amp. the circuit that puts it into safe mode is bad and that is a very small chip on the board know as a op amp. needs to be repaired.

Jan 25, 2010 | Alpine MRP-M500 Car Audio Amplifier

1 Answer

Speaker Fried, is my Amp toast too?


You are sending TOO much power to the speakers, Replace the speakers and then get a much smaller amp that is within the ratings of the speakers. ACTUALLY you should get an amp that is aboout 1/2 the total rating of the speakers.

You should ALSO procure a sound meter to verify the sound level is within safe limits. If you insist upon abusing your ears with too high a sound pressure, be ready to buy hearing aids at a VERY young age.

You also need to know that the enclosure of the speaker plays a part in keeping the speaker from tearing itself to pieces.

MANY of the auto sound system installers are hacks that don't do it right and you see what happens to your expensive equipment!

Using even a Radio Shack sound meter properly will protect your preciuos hearing for later life.

Dec 22, 2009 | Bazooka Car Amplifiers

2 Answers

I have a jl 1000/1 mono amp and my low ohm light was on and making a buzzing sound and found that there was a resistor that one of the terminals broke off and now no matter where i look i cant find the...


The 5 ohm could be challenging, what you could try is to get 2 10ohm 3 watt and put them in parallel. Will be 5 ohm and 10ohm is easy to get

Hope that helps

Jul 26, 2009 | Car Amplifiers

1 Answer

Need TIS t510pk wiring help


Grey = F/L-
Pink = F/R-
White = R/L-
Yellow = R/R-
Purple = F/L+
Red = F/R+
Green = R/L+
Brown = R/R+
Black = GND

Jun 06, 2009 | Car Amplifiers

1 Answer

Mackie 1400 overload lights on


hey Ron
use a larger ground wire it will stop the overload you may have to place it somewhere new but its the size of the wire that trips the overload feature too small and amp will go and protect itself (bigger ground better sound)
hope this helped

Feb 28, 2009 | Bob Mackie Mackie M-1400i Power Amplifier...

1 Answer

How do i know if my amp is blown


Hey Yoo,

 

Go to Radio shack and get you an adapter that will take an earphone jack and convert it to RCA male.  You use this to simulate the signal coming from the reciever.  Hook up to a Cd player or Walkman, anything with an earphone output jack. Test that the device actually puts out music or anything worth listening to.  Connect the device to the input of your amp, with the car running, and the reciever turned on.. This will tell yo if the signal is getting from the reciever to the amp. You may not be getting signal from the head unit. 

If you still get no sound to the woofers, dsisconnect the woofers and try a different speaker.  If that speaker dont work,  Change setting and switches., and if you still get no sound, then your amp is toast.

Oct 23, 2007 | Sony Xplod Car Audio Amplifier XM-DS1300P5...

1 Answer

Hifonics 1605


have you checked Radio Shack? they have a lot of cicuit board stuff for soldering

Apr 26, 2007 | Hifonics BX1500D Car Audio Amplifier

1 Answer

Kenwood KAC-749S


Try to take out the lights that you put in yourself, but do it carefully, as you might have bridged out the power connectors that go through to your subs.

Mar 28, 2007 | Kenwood KAC-749S Car Audio Amplifier

Not finding what you are looking for?
Car Amplifiers Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Amplifiers Experts

Tygh Duval
Tygh Duval

Level 2 Expert

290 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Car Amplifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...