Question about Freud FT2000E 3 Router

Open Question

My FT200E freud router stopped working when I was setting up a new jig. No evidence of any burnt wiring etc. Any ideas?

Posted by on

  • blonsan Nov 04, 2010

    Anybody?

×

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 211 Answers

SOURCE: freud 3 one fourth plunge router variable speed won't run

Hi

First check the power suply cord(conductivity),the on/off switch, the fan and the armature,the brushes and the wires.

best regards savumihai71

Posted on Feb 12, 2009

rowdy45176
  • 2176 Answers

SOURCE: Freud FT2000E Brushes

You have a couple options, I found a website for Freudtools.com where you can find a dealer near you or you can call Freud direct at 1-800-334-4107 to order the brushes. The part number I saw that you need is 13413.9073 but you might want to double check me on that . let me know if I can help further

Posted on Feb 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Freud ft3000vce has stopped running. Was running fine, turned it on and it wouldn't rev up to full rpms, then died. What's wrong with it?


Hello Robert my name is Larry I am a service dealer for freud canada.It sounds like the speed controller is on the fritz.It always happens like that--the controller is about 90.00 canadian and the bad news is Bosch has purchased and it is not suppling many parts anymore..
but the modules are still available.
Thanks
Larry
haltonmaintenance@yahoo.ca

Dec 26, 2011 | Freud FT3000VCE Router

2 Answers

Would any one know where to get parts for and Freud FT2000E online. I am looking for a new switch.


Hello George,My name is Larry I am a service tech for Freud Canada.
I can get for you almost any Freud parts
larry_boccioletti@yahoo.ca

Dec 19, 2010 | Freud FT2000E 3 Router

1 Answer

I need an operator's manual for the SBOX8 Freud so I know how to set up the jig.


http://www.freudtools.com/images/PDF/sb_dado-n-accessories.pdf

Page 6 of this PDF goes over how to set up the Cutter Set. Freud is not offering a manual for this peticular set. I hope this helps.

Nov 29, 2010 | Freud 8" Box Joint Cutter Set - SBOX8

1 Answer

My Ft2000E Freud router stopped working when I was setting up to run some moldiings. No humming . no burning= nothing. Any Ideas?


Hello Blonsan I am a service dealer in Canada and the speed control will do that no warnings ---the speed control is 89.00 canadian ---give or take--

Nov 04, 2010 | Freud FT2000E 3 Router

1 Answer

How to setup a jig for handheld router


Hello. here is a basis jig that will give you all of the fundamentals - from there you can experiment further:
http://www.doityourself.com/stry/making-a-router-jig

Jan 25, 2010 | Speed Black Decker 10 Amp Variable Router

1 Answer

Ive got a kenzo router and the router bits do not fit . ive got quarter inche cutters and when the collet is done up tight the cuters are still not tight. its not a half inch router as ive measured it. any...


Your router bits must have a 6mm shaft, whereas your router with the collet closes down on a 1/4" or 6.4mm shaft. You will need to get a metric collet for your router spindle, or get a new set of 1/4" bits

Sep 28, 2009 | Freud FT2000E 3 Router

2 Answers

Freud FT2000E Brushes


You have a couple options, I found a website for Freudtools.com where you can find a dealer near you or you can call Freud direct at 1-800-334-4107 to order the brushes. The part number I saw that you need is 13413.9073 but you might want to double check me on that . let me know if I can help further

Feb 18, 2009 | Freud FT2000E 3 Router

1 Answer

Freud 3 one fourth plunge router variable speed won't run


Hi

First check the power suply cord(conductivity),the on/off switch, the fan and the armature,the brushes and the wires.

best regards savumihai71

Jan 05, 2009 | Freud FT2000E 3 Router

Not finding what you are looking for?
Freud FT2000E 3 Router Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Freud Tools & Hardware - Others Experts

freddyfox

Level 2 Expert

236 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Tom Chichester

Level 3 Expert

33272 Answers

Are you a Freud Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...