Question about eMachines ET1641-02w (PT.NA60X.001) PC Desktop

1 Answer

Powers on for 5-6seconds then beeps one time and shuts down

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 1,082 Answers

Here are the beep codes for common BIOS programs:

1 BeepA single beep from an AMI based BIOS means there has been a memory refresh timer error. The solution is often to replace the RAM in the computer.

A long beep from AWARD is probably memory error.

1 short beep from AWARD bios & PhoenixBIOS and most others is a positive ok signal.

Without more information, it sounds like it is a memory problem. Remove the memory and see if it will boot to the BIOS/setup screen. If so and you have multiple memory sticks, put one in and try to boot. If that fails try the other.

Posted on Aug 20, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lenovo desktop 3282 beeps twice then 5 times and goes no further


Follow these steps to clear the password:
NOTE: These steps also clear CMOS.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the real-time clock (RTC) battery
6. Wait approximately 30 minutes.
7. Replace the RTC battery and reassemble the computer.
8. Connect AC power to the computer. Do not reinsert any batteries at this time.
9. Turn on the computer.
All passwords and all CMOS settings have been cleared.

Aug 01, 2012 | Lenovo Computers & Internet

Tip

Beeps 3 times; shuts down;lens won't retract


I had a Polaroid i531 that would beep 3 times then shut down & the lens wouldn't retract.

I fixed it like this:
  1. Inspect the lens from all angles and you'll see that the lens assembly is out of sync. (My was looking upward ever so slightly)
  2. Using gentle finger pressure, press in the opposite direction of the abnormal lens direction
  3. I heard a snap, then I powered the camera on.
  4. Camera now works.

on Jun 28, 2008 | Polaroid i531 Digital Camera

2 Answers

I turn on my ps3,tv displays message..invalid format... what can cause this,how to fix it?


Hi there, your display needs resetting back to standard resolution, please follow my guide on how to do this -

http://www.fixya.com/support/r6784945-playstation_3_no_display

Thank you for using FixYa

Dec 27, 2010 | Sony Playstation 3 (PS3) Console

1 Answer

Hi, my ps3 shutting down when I turne on the power


try rebuilding the database and the file system in recovery consol

to get to the recovery consol press and hold the power button when ps3 is in standby mode(red light) till you hear a double beep. sometimes the ps3 does a beep then another beep and goes back into standby thsi is fine just release the power and quikly press and hold it again till you get double beep.

like on my 80g system it goes like this

ps3 standby...press hold power.......beep .........beep........stanby again....release and hold power again.......beep .........double beep...release power now you should be in recovery menu.

Oct 27, 2009 | Sony PS3 40GB Best Sellers Bundle Console

1 Answer

It is beeping "Error" with 5 beeps


5 beep error means that the waste ink tank is full. You can reset the counter to make it print by doing the following: You have to be exact. If you make a mistake in any of it, just go back to the beginning and start it all over.

1.Unplug the power cord from the printer

2.Hold down BOTH the POWER and RESUME button at the same time and then plug the power cord back in. Keep holding down the buttons until the printer finishes its powering up noises.

3.After the printer is quiet, release the POWER and RESUME buttons. Then hold down the RESUME and CARTRIDGE buttons at the same time with one hand, and press the POWER button with the other. KEEP HOLDING DOWN the RESUME and CARTRIDGE buttons until you hear 2 beeps. They will come quickly together and one beep will be longer than the other. Listen carefully, as they are not very loud.

4. Once you hear the 2 beeps, release both buttons.

5. After both buttons have been released, then press the CARTRIDGE button 15 times. You will hear a beep each time it's pressed.

6. After you finish pressing the cartridge button 15 times, then press the RESUME button one time. The printer will beep and shut off.

7. Turn the printer back on by pressing the POWER button. The printer will work fine now. The waste ink will have been reset to 50% full.

Sep 29, 2009 | Canon BJC-85 InkJet Printer

1 Answer

Jvc mc200 powers up,beeps and shuts down within 2 seconds


have a jvcgr-smx750 . It was working fine but recently I powered it up with battery, without battery and just ac power cable. Both times it does power up and shows the screen for about 2 seconds, beeps, and then shuts off. Please help

Apr 12, 2009 | JVC Video Cameras

1 Answer

When powering up I get 2 short beeps and one long one.


The beep code is signifying either improperly seated/ bad ram or improperly seated/ bad video card. Since you replaced the RAM I would say it would be a bad video card. Replace & reboot. Hope this helps & please remember to rate my answer. Thanks.

Jan 22, 2009 | Toshiba Tecra S1 Notebook

1 Answer

My laptop keeps making beeping sounds when i type.HELP!!!


Do a system restore to a point previous to the power failure shut down. It sounds like the abrupt shut down glitched the system.

Jul 13, 2008 | Dell Inspiron 1501 Notebook

Not finding what you are looking for?
eMachines ET1641-02w (PT.NA60X.001) PC Desktop Logo

375 people viewed this question

Ask a Question

Usually answered in minutes!

Top eMachines Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Avishek Samaddar
Avishek Samaddar

Level 3 Expert

639 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18402 Answers

Are you an eMachines Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...