Question about AOpen MX46L Motherboard

1 Answer

What is the ram frequency for mx46l aopen board

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 106 Answers

This motherboard has two 184-pin DIMM sockets that allow you to install DDR 266 memory up to 2 GB.

Posted on Aug 20, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an AOpen vKM400Am-S Motherboard, when i turn it on a red light and cpu fan turns on but no video to my monitor,i checked if my video card works on a difrent pc and it did, my pc wont turn on


this caused by RAM error, open your computer, disconnect ram, turn on your computer?is computer beeping, 1 long and 2 short beep??if yes the problem is come from your ram, clean your ram connection then connect ram to mother board, turn on your computer, is the video come to screen??if no, try to connect another ram to your computer, for sure use new ram
i hope this helpful
thank you for using fixya

Feb 05, 2011 | AOpen MX4LR (91.89Y10.002) Motherboard

2 Answers

Need graphics card drivers


Is the graphics supported on the motherboard or is there an expansion slot card for video graphics?

Dec 12, 2009 | AOpen MX46L Motherboard

1 Answer

Support prosesser


Fixya do an online manual for this motherboard here

The product specs can be found here

According to this page your Motherboard accepts a Pentium 4 processor on a socket 478 and a FSB of 400MHz so I would think it should support up to a 3.2GHz processor.

Hope this helps

Jun 28, 2009 | AOpen MX46L Motherboard

1 Answer

POWER SW cable: Old cabinet and Acer stock motherboard.?!


Here is the download site for Aopen motherboard. Download a manual and i am sure that the locations that you are looking for wil bbe illistrated. If not their are also 4 more pages of downloads for that MB.

http://download.aopen.com.tw/Default.aspx

Jan 05, 2009 | AOpen MX46L Motherboard

2 Answers

Added ram, now wont boot long beep


try removing the ram and try again

Jan 04, 2009 | AOpen AX4B-533 Motherboard

1 Answer

Power up problems


To enter setup (Refering to the bios/cmos), press the Delete key very two seconds untill the bios main menu loads. You need to go to the menu heading - Boot.
If you added another hard drive to you're system the IDE (hard drive) it's jumper settings may not be correctly set. If there are now two IDE drives both the primary master & secondary drive's jumpers must be set correctly. You will ned to look at the white sticker on the drive for the correct jumper settings. Many primary IDE drives pin jumper is set as a single master drive with out a secondayr drive attached in the system. When you add a second drive the pin jumper one the master drive will most likely need to be changed to master with a slave. The second drive will also need it's jumper set as a slave drive. Once this has been adjusted you need to enter the bios & make sure you're primary master drive is set in the boot order. Most PC's boot order is as follows.
1st Boot device, floppy drive. (If one is connected to the system).
2nd boot device, CD-ROM drive.
3rd boot device, master IDE drive.
Please use the help of you're manual to guide you for these settings.
AOpen MX46L web site. http://download.aopen.com.tw/Default.aspx
You must set the three drop down menu's to get you're board's drivers & manual. In the first menu choose motherboard, in the second menu choose MX46L & in the last menu choose manual. For drivers, the third menu choose drivers.

Still heave more questions? Just ask.
Mike

May 18, 2008 | AOpen MX46L Motherboard

1 Answer

I have a problem


Suggest you replace the keyboard & or try another keyboard & see if that fix's you're trouble.

Mike

Apr 16, 2008 | AOpen MX46L Motherboard

2 Answers

Cpu size


Hi handydak

For your Mobo
VKM400 AM-S Try this link it will tell you what max size CPU & Memory you can install to improve performance.http://download.aopen.com.tw/Default.aspx

Regards,

ajb2000

Dec 28, 2007 | AOpen vKM400Am-S Motherboard

1 Answer

Im having serious probs here


first, ensure that only one master hard drive is connected (also disconnect cdrom(s). Next, at startup press the key (DEL or F2) to BIOS screen. then make sure that only the master hard drive in position 1 is listed or choose AUTO detect. now reboot and report if any progress. If no further progress, then master hard drive has failed somehow, but to be certain, try that drive on another pc as a slave just to test spin-up.

Sep 08, 2007 | AOpen MX46L Motherboard

Not finding what you are looking for?
AOpen MX46L Motherboard Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top AOpen Computers & Internet Experts

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

David
David

Level 3 Expert

778 Answers

Gareth Cockram
Gareth Cockram

Level 3 Expert

661 Answers

Are you an AOpen Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...