Question about Microsoft Flight Simulator X for Windows

1 Answer

Tail wheel planes go round in circles when taxiing

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Has the tail wheel been locked when trying to turn

Posted on Aug 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

NAME OF SONG WITH FOLLOWING LYRICS: "MY HOUSE IS IN ORDER AND MY BAGS ARE PACKED"?


"All My Bags are packed, I'm ready to go.
Taxi's waiting, blowing his horn"


"Leaving on a Jet Plane", Peter Paul and Mary

Feb 08, 2017 | Computers & Internet

1 Answer

MY SKY ROVER HELICOPTER TAIL SPIND A CIRCLE


the trim is out of line, for the love of god watch some beginners videos on setup.

Mar 26, 2016 | WowToyz IN-EZRU Propeller Powered Giant...

1 Answer

Which Terminal does Vietnam Airlines come in too from Saigon.


This airline flies from HCM City to both Melbourne and Sydney. So which one is your destination? Alternatively what is your VN flight number ?

In Sydney you would land at the International Terminal and clear Customs through either exit gate A or B. You can then join a short queue outside for a taxi (which is rarely a long wait), or go to the pre-booked taxi bay. Cab drivers are not allowed to leave the car to collect you inside (only tour company drivers can). The taxi concierge outside will direct you to the right place.

Jan 10, 2015 | Cars & Trucks

1 Answer

Reset on board computer


Check fuses or replace tail light globe

Jul 09, 2014 | 2003 BMW 325i

1 Answer

Wife has Kenmore 385.12314. Regular use. Normally cleaned and oiled. Needle goes down, but bobbin thread doesn't catch. Needle at bottom of stroke and "half moon" is on top, needle...


Make sure the needle is in the machine correctly- all theway up into the needle bar, make sure that it is threaded correctly, etc. Ifthis all checks out ok, take the bobbin case out of the machine. There are twoears on either side of the bobbin case- turn the left one to the left and theright one to the right. Remove the silver ring, and inspect the piece of metalthat the ring came off of (looks like a circle with the top cut off). You haveto locate the hook which is the piece that looks like a half moon inside thebig round metal piece. Locate the tip of it, turn the hand wheel toward youuntil the needle is in the lowest position, at this point the tip of the hookshould be flush with top of the left side of the cut off circle. If this is notso, your machine needs to be re-timed. If that is the case, I would need to seea picture of the bottom of the machine so that I am able to determine whatneeds adjusting. Make sure you're turning the hand wheel in the proper direction-- the proper direction isthe one that will feed fabric forward under the presser foot.

Make sure the needle is facing in the correct direction -- stitches don't form,or skip badly when the needle is turned around.

Put the bobbin in the bobbin case (right way around) leaving a 2-3" tail.

Thread the top of the machine correctly, leaving a 3-4" tail afterthreading the needle.

Hang on to the end of the upper thread, and use the hand wheel to drop theneedle... continue to turn the hand wheel to raise the needle. Pull on the endof the needle thread and a loop of bobbin thread should come up.

Hold BOTH threads behind the presser foot when starting a seam to preventthread jams.
Hope this will help you. Good Luck.

Aug 17, 2011 | Vacuums

1 Answer

Finding area of a concentric circle


You find the area of the larger circle. Then find the area of the smaller circle. Then to get the area of the ring, you subtract the area of the smaller circle from the larger circle.

So basically:

Area of larger circle - Area of smaller circle = Area of ring

http://www.vitutor.com/geometry/plane/concentric_circles.html
pi. r2 = area 2pi. r=circumference of circle.

Read more: http://wiki.answers.com/Q/What_is_the_Formula_for_concentric_circle#ixzz1Cv8wAOJf

Jan 30, 2011 | Computers & Internet

1 Answer

Phil and ted vibe, wont lock and front wheel issues


The Vibe is very fussy to fold and has driven me up the wall on a few occaisions. To get it to lock when folded, the handlebar must be in the fully raised position - I think that is the secret. (The basket should also empty - we keep the raincover in there and it can obstruct when folding.) As for going round in circles, perhaps check that both rear wheels are inflated to the same pressure - but there's no doubt that the front wheel has a mind of its own, particularly at slow speeds or when starting off. Hope this is of some help.

Nov 22, 2009 | Regal Lager Phil & Teds Vibe Jogger

2 Answers

Frustrations


Your graphics problem is due to graphic rendering. you should either decrease the game play resolution or upgrade your graphic card if the problem still persists.

Jun 05, 2009 | Microsoft Flight Simulator X for Windows

Not finding what you are looking for?
Microsoft Flight Simulator X for Windows Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Microsoft Video Game Consoles & Games Experts

marley mcelhinney

Level 3 Expert

490 Answers

Tre Elkins

Level 3 Expert

643 Answers

Martin Murray

Level 3 Expert

1623 Answers

Are you a Microsoft Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...