Question about Phones

1 Answer

Probelm with registering additional headset for the philpsse 7450

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 34 Answers

OK here it is leave the additional hand set base plugged in & take the hand set with you to the main phone & base. 1. unplug the main base.
2. with the main base unplugged hold the find handset button on the base.
3.with your finger still on the find hand set button plug the base back into the power.
4.charge light on main base should be flashing.
5.while the light is flashing press & hold the hash # button on the additional hand set only until it says registration complete & its all done.

Posted on Aug 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I auto answer using Plantronics Headset (Savi W740) on a Mitel 4250 Phone?


Plantronics makes an adjunct device that attaches to the telephone base (Velcro) and can lift the handset when the button on your headset is pressed. Unfortunately that's the only way to directly integrate the Plantronics (or any other brand) headsets with the Mitel 4XXX series phone. This handset lifter is actually bundled with some of the SAVI headsets, depending on the actual model you get. Separately it's about an additional $50 option. I recall the Plantronics part number is HL-10. Hope this helps.

Jun 19, 2014 | Mitel Phones

1 Answer

Uniden registering


Follow the registration instructions beginning on page 5 of the DWX207 manual at http://www.uniden.com/content/ebiz/uniden/resources/ownersmanuals/DWX207om.pdf

May 15, 2013 | Uniden Cordless Phone

1 Answer

Want to register an additional handset for panasonic kx-tga9341t


You need to contact Panasonic's customer service.

May 01, 2012 | Panasonic Phones

1 Answer

I want get pin code to register headset to the base


Hi I ave the Siemens giaset AL145 hand display the pls Register.
Pls help us to slove the problem

Regards
Vinod M B
India
+919916134485

Aug 19, 2010 | Siemens Gigaset S450 Cordless Phone

1 Answer

Vtech Dect 6.0 says not registered. how do I register?


Instructions for registering additional new handsets on VTech Model DS6151: Place additional handset on main base. Press HOLD on main base and # on handset. Asks you to de-register. Press no. Registration of additional handset takes place.

Aug 17, 2010 | Vtech DECT 6.0 Digital Cordless Phone

1 Answer

Only bass set going extra hand set not working


Hi,


This is because the extra handset might have not been registered with the base unit.The headset should be register to use the headset with that base unit.

To register the handset to base unit please follow the instruction:-

On registration the handset is allocated a handset number for use on the new base unit, the handset numbers are 1-5.

1. Press and hold
d65e3ff.jpgon the base unit until 608a95f.jpgstarts flashing. Registration mode will remain active for approximately 3 minutes.

2.Press and hold both
19efd34.jpg together until you hear a long beep.

3.Select the base unit you wish to register by pressing the corresponding number button 1-4.
4. When PIN is displayed, enter the units PIN number (0000 for this model).
5. If the registration is successful the handset will return to standby mode in a few seconds.


Thanx

Jul 22, 2010 | Doro DECT 540 Cordless Phone

1 Answer

Phones won't Register!!


It is possible that you have maxed all of the headsets that can connect to the base. Yes, the base can support 10 headsets, but there is a small chance that in some way you registered more to the base or you purchased a base that had phone registered to it that are not in your possession. Either way, if the base is maxed out, you will not be able to register any additional headsets to it. The only option is to do a factory reset of the base unit if this happens to be the case. This is done as follows according to Uniden Tech Support:

1. Disconnect the power from the base

2. hold down the following three (3) keys: [dnd] + [middle soft key] + [*]

3. While holding down the keys, plug in the base (hold the keys down until you hear a long beep). This is supposedly all it takes to reset the phone.

The way to determine the number of hand sets tied to the phone is to press the intercom key on the base and scroll through the list of phones. if you see more than the number you anticipate still being tied to the base, you will have to utilize the above procedure.

Jul 27, 2009 | Uniden TCX905 Cordless Accessory Handset...

1 Answer

Whole house ringing when cordless phone is used


try deleting all headsets using primary headset (marked with no.1): 4-base/8-deregister/default pin '0000' and register them again using each headset (3-headset/8-register/same pin). it worked for me.

Oct 20, 2008 | Phones

1 Answer

Registering a new cordless handset


It doesn't exactly "register" but you turn it on via phone programming.

Just plug it into the headset jack, then select a button to program and press PROG (the button) and dial 67 enter.

When you press the button, the light will turn on and the display will say HEADSET ON. Pressing it again will turn it off.

Carl

Sep 28, 2008 | Panasonic KX-T7633 Corded Phone

Not finding what you are looking for?
Phones Logo

Related Topics:

349 people viewed this question

Ask a Question

Usually answered in minutes!

Top Phones Experts

kakima

Level 3 Expert

96396 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Cindy Wells

Level 3 Expert

4754 Answers

Are you a Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...