Question about Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

LXIH, ML #130017

Unit turns on, fills, and washes properly but immediately after the rinse cycle the display fully lights up and count up (11, 22, 33, etc) occurs followed by Pd, because the sump still has water in it, and then it starts the fill cycle as if it was just turned on, then when it times out it is ready to go. replaced relay board, control board and membrane switch (which i thought would take care of the problem) still doing the same thing...any help would be greatly appreciated as i am at my wits end !

Posted by on

  • mushmouth May 03, 2008

    no blockage problem, it pumps out just fine. the wash/rinse program works fine, it;s after it's done is the problem

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 75 Answers

Hi there have you checked that the drain pump is pumping out the water fast ehough, sounds like you may have a blockage problem and the programe is timeing out ie. not draining within the specified time, for example 3 mins

Posted on May 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have Hobard LXIH dishwasher, it is working OK but during rinse cycle instead of taking in rinse agent it is actually fill rinse bottle back with water. Rinse pump is working, it was replaced in June


Check the rinse pump. The tubing needs to come from the supply into the bottom of the pump, and the pump should be running clockwise. If the pump tube is worn, the rinse pressure will blow through the pump filling the bottle

Dec 12, 2013 | Hobart Dishwashers

1 Answer

Hobart ml 130017


There is a temp booster on that unit. A rinse temp of 190 is not out of the range of specifications. If it is too hot, you should adjust the incoming water temp

May 30, 2013 | Dishwashers

1 Answer

Unknown control panel symbols bosch dishwasher super silent


Wash Cycle Options

Delay Start (model dependent):



This option allows you to delay the start time of your dishwasher up

to 19 hours.

Sanitize:



The Sanitize feature is available only in the Heavy, Auto, Normal and Half Load cycles. Press the

"Sanitize Option" button to activate the Sanitation features during these cycles. The technical sanitation

measures may also improve the drying results. The sanitize LED or The "Water Pipe" symbol will light when sanitation

requirements are met.

Note: The dishwasher automatically defaults to Auto Wash when turned off and back on. If you used the sanitize option
in your last cycle, the dishwasher will default to Auto Wash with the Sanitize option selected when you turn it on.

To achieve proper drying, always use a liquid rinse aid, even if your detergent contains a rinse aid or

drying additive.



Note: The dishwasher indicates low rinse aid by turning on the Refill Rinse Aid indicator LED (for units without

a display) or The "Spray Looking" symbol (for units with a display).

If this light is on, you need to refill the rinse aid dispenser

I got the idea that the "squiggly arrow" has something to do with the sanitize feature also. If you post your model number "on the inside right hand side of your dishwasher door" I'll go get your manual and post the link here. Hope this helps so far! :)

Jun 18, 2012 | Bosch 500 Series SHX55R55UC Fully...

1 Answer

Hobart LXIH stuck in Wash mode after running multiple loads. Shutting off breaker for several hours fixes problem until multiple loads have been run again and then it is once more stuck in Wash mode.


How long does it stay in the wash cycle? Indefinitely? Does the display continuously show "WASH"?. If it stays in the wash cycle indefinitely (i.e. continuously shows "WASH" for significantly beyond approx. 3 minutes), it's probably a control board malfunction. If it continues to wash after the "WASH" indicator goes out, it could be a shorted wash motor relay on the relay board or a fauly control board.

If the internal rinse water booster heater doesn't reach it's programmed setpoint temperature in time, the dishwasher will run an extended wash cycle to give the booster heater more time to finish heating the rinse water. If this is what's happening, the wash cycle would last approximately 3 minutes, then it would rinse regardless of whether the booster heater has finished heating or not.

The booster temperature thermistor may be bad, giving a false booster temperature reading, causing an extended wash cycle as described above. The booster heater elements or contactor may be bad, preventing the booster heater from heating and reaching proper temperature, also causing the same extended wash cycle to give the booster more time to heat.

Jan 06, 2011 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

How much delime agent should I use to clean the system in a Hobart LXI-H?


Depending on how often you delime the dishwasher use 2 cups.The delime light will come on after 1000 cycles set from factory default.If the delime icon is lit and beeps,turn the unit off.

Push and hold the delime/wash button and on button for 5 seconds and youll be in delime mode.

The unit will fill and heat up and display "add delime".Open the door add the delime and press the wash button.The dishwasher will run for 5 minutes then rinse and drain twice then shut off.When you turn it back on the delime icon will be gone.I'm a hobart tech and repair these dishwasher often,any questions let me know and please rate me,Thanks.

Nov 24, 2009 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

The dishwasher has been running for 3 hours and seems to be stuck on 1 minute left. Upon opening, there was sudsy water remaining in the bottom, but the dishes looked clean. The washer just won't go to...


SHU 53 MODELS To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ ?21? = version 1 with jumper). When wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button. To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display alone). Cycle Countdown display will show ?88″ when REGULAR WASH button is pressed and ?8h? when Delay Start button is pressed. To start testing, press both the SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended, Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added together, (e.g./ ?6? = faults 2 + 4). 0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault 1 = Aqua Sensor (?Sensotronic?) fault 4 = Filling fault F = Filling fault (display occurs during wash, not test) To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty. If water level switch (f1) has failed (opened), display will show fault code ?4″ and unit will continually fill and drain where testing won?t be completed. If flow switch (e5) has failed (opened), display will show ?0″, water won?t heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code ?8″ immediately and testing will end shortly after water has started circulating.

Aug 01, 2009 | Bosch SHU5315UC Dishwasher

1 Answer

Bosch SHU 6800 Water hot at sink only luke warm at the washer


BAD CONTROL BOARD TO TEST TO SEE IF THIS IS THE ISSUE RUN TEST PROGRAM
To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by
pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ “20” = version 0 without jumper). When
wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button.
To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and
REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display
alone). Cycle Countdown display will show "88" when REGULAR WASH button is pressed and "8h" when Delay Start
button is pressed.
To start testing, press both SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended,
Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added
together, (e.g./ “6” = faults 2 + 4).
0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault
1 = Aqua Sensor ("Sensotronic") fault 4 = Filling fault F = Filling fault (display occurs during wash, not test)
To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil,
measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays
at ~ 1.5-2 A, then heater, high limit or flow switch are faulty.
If water level switch (f1) has failed (opened), display will show fault code "4" and unit will continually fill and drain where
testing won't be completed. If flow switch (e5) has failed (opened), display will show "0", water won't heat (to 150ºF) and
water won’t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code "8" immediately and
testing will end shortly after water has started circulating

Jul 18, 2009 | Bosch 24 in. SHU43 Built-in Dishwasher

2 Answers

The hobart lxih is stuck in delime.


To reset or clear delime message, on control board there are 3 buttons. from power off, drawer open, manget on door switch, door closed, hold PROG on board and press the ON key on keyboard. pressing select moves to next poption, up arrow increases setting. step through select until you see delime, settings for LXi are de for disabled, and 1 through 65= x100 cycles. rg if set at 5, after 500 cycles the message apears. To keep the settings and clear the message a delime sequence needs to be run precisely as described.

DO NOT MIX DELIME ACID, RINSE AGENTS OR OTHER ACID WITH BLEACH PRODUCTS, OR HAZAEDOUS GASES WILL FORM.

With machine off, remove rack , close door, press and hold wash/delime key and press ON. Delime will be lit on display, release wash/delime key, and let machine fill. you should then see ADD and DELIME on the display, open the door and add the delime agent following supplier's instructions precisely. close the door, press wash, delime will flash. After delime is complete power is turned off. Inspect the machine and repeat if necessary.
DO NOT LEAVE THE ACID IN ANY LONGER THAN RECOMMEDED.

Jun 18, 2009 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Not able to enter program mode


You need to remove the conrol drawer.Open the door,look at the top and there will be 2 screws,remove the screws then slide the control box toward you.You will see 2 circuit boards,the one to the right is the control board.You will see 2 white buttons marked prog and select.Hold the prog button in and the on button.You should now be in the program mode.

Mar 31, 2009 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Odd operation


This unit is a sanitizer, not a full fledged dishwasher. It is designed for restaurants and bars where the primary use is washing glassware. The behavior you describe is normal for this model. The manual can be found at the following link:
https://feg.hobartcorp.com/resourcecenter/ProductDocumentation/F34779%20Rev%20B.PDF

Jun 15, 2008 | Hobart 24 in. LXIH-3 Built-in Dishwasher

Not finding what you are looking for?
Hobart 24 in. LXIH-3 Built-in Dishwasher Logo

Related Topics:

318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Ricardo311

Level 1 Expert

36 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

handygirl911
handygirl911

Level 2 Expert

55 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...