Question about Sears Craftsman LiftMaster Chamberlain Garage Door Opener Wireless Keypad Model 976LM Security+

1 Answer

Liftmaster 724LM Pug-in Light and Appliance Control

I have lost my instructions to program this device. Currently using Sears Grey 3 button remote.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 244 Answers

Does it have a learn button. push it and push remote button.

Posted on Jan 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Liftmaster security + remotes do not operate. I bought 2 new remotes and neither one of them will program to operate the opener either.


Yes it sounds like the board. Make sure the opener is not in lock. If the light in the wall control is blinking press and hold the lock button for 3 seconds.

Jul 29, 2012 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

I have the Liftmaster Chamberlain Professional Formula I model 102.1499A and for some reason, the learn button will not sync with the homelink on two of my cars. Is there a way to reset the learn button? ...


Here is the information I have for homelink.

  1. Clear out anything previously programmed into the in-car system from the factory by holding down on the 2-outside buttons simultaneously, until the in-car LED starts flashing rapidly. This may take up to a minute (in most cases, the key should be on auxilary, and/or the car door must be shut).

  2. Decide which button you want to make to be your in-car garage door transmitter. Hold your transmitter up near the selected button, pressing both the garage door remote and the selected in-car transmitter button simultaneously. Hold down on the buttons until the in-car, LED light flashes rapidly. This sets the in-car remote transmitter to be your garage door openers make transmitter, but you are not done. You now need to make this in-car transmitter your personal transmitter.

3. Go to the Learn Button on your garage door opener. The button is usually next to the area where the floppy antenna is connected to the motor head. With Genie it is most often behind the light lens, and an indicator light flashes red when pressed. With Sears or Liftmaster (Chamberlain) it is near, or part of, the terminal screw board, and is a red, green or purple square button with a green, amber or purple indicator light. Press this learn button momentarily. The indicator light will turn on and blink if Genie or otherwise stay lit. For Genie systems, go back to the in-car transmitter button you programmed and press this button 3 or 4 times, or until the door starts moving. This should set your in-car transmitter to your garage door opener. For Liftmaster, Sears, or Linear Megacode press and hold the in-car button you programmed until the garage opener light flashes. Your in-car is now programmed to operate your door.



Jan 04, 2011 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

I have a liftmaster 1255km(model) with a clicker remote opener model KlIk2. All devices that were used to open the garage lost the ability to open. I have reprogrammed all devices including hand held...


I think you are saying everything except the Klik2 has quit working. If that is so check to see if the light in the wall button is blinking. Press the 'lock' button for 3 seconds and the light should glow steadily and the remotes will work. If you are saying all remotes plus the Klik2 has quit then your logic board has failed.

Sep 25, 2010 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

I have a chamberlain garage door opener. It came with an appliance control remote control. How do I set it up? when I plug my light into it, I can push the button and turn on the light but the remote...


Plug the appliance control into a 120 Volt outlet.

Press and release the "learn" button on the appliance control. The learn indicator light will glow for 30 seconds.

Within 30 seconds press and hold the button on the hand-held remote.

Release the remote control push button. Code setting is now complete.

Aug 22, 2010 | Sears Craftsman LiftMaster Chamberlain...

2 Answers

How do you clear and re-enter a new code for wall mounted remote


To change the code you need to locate the smart/learn button which is near where all those white wires go. Press and immediately release it and then walk over to your keypad and key in any 4 digit code you like and press enter.

See if this works for your car.

  1. Clear out anything previously programmed into the in-car system from the factory by holding down on the 2-outside buttons simultaneously, until the in-car LED starts flashing rapidly. This may take up to a minute (in most cases, the key should be on auxillary, and/or the car door must be shut).
  2. Decide which button you want to make to be your in-car garage door transmitter. Hold your transmitter up near the selected button, pressing both the garage door remote and the selected in-car transmitter button simultaneously. Hold down on the buttons until the in-car, LED light flashes rapidly. This sets the in-car remote transmitter to be your garage door openers make transmitter, but you are not done. You now need to make this in-car transmitter your personal transmitter.
3. Go to the Learn Button on your garage door opener. The button is usually next to the area where the floppy antenna is connected to the motor head. With Genie it is most often behind the light lens, and an indicator light flashes red when pressed. With Sears or Liftmaster (Chamberlain) it is near, or part of, the terminal screw board, and is a red, green or purple square button with a green, amber or purple indicator light. Press this learn button momentarily. The indicator light will turn on and blink if Genie or otherwise stay lit. For Genie systems, go back to the in-car transmitter button you programmed and press this button 3 or 4 times, or until the door starts moving. This should set your in-car transmitter to your garage door opener. For Liftmaster, Sears, or Linear Megacode press and hold the in-car button you programmed until the garage opener light flashes. Your in-car is now programmed to operate your door.



Feb 02, 2010 | Sears Craftsman LiftMaster Chamberlain...

2 Answers

Liftmaster 1/3 HP. Remote and wireless keypad stopped working.


Sounds like the reciever for you wireless devices is not working?

Aug 01, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Sears Model 3 41A4315-7D Have 2 remote controls and one keypad. I reset all the codes and I can follow the instructions and program one device, any other device will not program after the first device is...


You might try programming them this way if you haven't already.

Press and hold the button down on your remote and then press and immediately release the smart/learn button. Do this for both remotes.

Press and immediately release the smart/learn button and then walk over and key in your 4 digit code and press enter on your keypad.

What was the problem that made you decide to "reset the codes"? May be a clue to your problem.

Jul 07, 2009 | Sears Craftsman LiftMaster Chamberlain...

3 Answers

Remote missing on old dominator garage door opener


This is the most complicated way I know of coding a remote and I am a tech. who does this all the time.
Turn power off. Wait 3 sec's & turn back on. Quickly press program button on back of box twice. Lights will flash, bottom light will stay on. Press program button twice, & No. 3 light will start flashing. Press and hold your remote button until light stops flashing. Code will be accepted.

Apr 11, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Cant turn off lock button on craftsman control consol 53687


You need to hold the lock button for 3 seconds. If the green LED in the wall control is blinking off and on the door is locked. If holding the button in for 3 seconds doesn't work you can try programming your remotes. This sometimes works. Press and hold the button on your remote while you press and immediately release the smart/learn button on the motor unit.

Apr 06, 2009 | Sears Craftsman LiftMaster Chamberlain...

Not finding what you are looking for?
Sears Craftsman LiftMaster Chamberlain Garage Door Opener Wireless Keypad Model 976LM Security+ Logo

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sears Garage Doors Experts

Al Clark

Level 2 Expert

290 Answers

Cindy Wells

Level 3 Expert

4757 Answers

Pieter Vleeshouwers

Level 3 Expert

1417 Answers

Are you a Sears Garage Door Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...