Question about Vacuums

1 Answer

I want to install a belt on the turbo power 2000 upright vacum cleaner , What do I have to do to install it. The old belt broke.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Legend:

    An expert who has written 200 answers of more than 400 characters.

  • Expert
  • 310 Answers

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=564997
Generic problem for all Vacuums
I want to install a
Posted by mcpo on May 02, 2008
I want to install a belt on the turbo power 2000 upright vacuum cleaner , What do I have to do to install it. The old belt broke.

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
There are only 2 ways you can install a belt on a Turbo Power 2000, either you can remove the bottom plate and expose the belt, 1st place the belt on the brushroll section of the vacuum then use a belt puller or a screwdriver with a left or right hook @ the end and pull the belt onto the motor pulley, once you get the flat belt onto the motor pulley than you do what is called tracking to straighten belt out so it runs straight, replace the bottom plate. 2nd then remove the top cover by 2 to 4 screws or levers and then remove the top, then follow the procedure listed above. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.
Don – The Vac Man
Go Ahead. Use Us.

Posted on May 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air driven turbo brush


Is this the Lightning model? How old is it? You may have to just replace the belt.

Also, the front brush motor will not engage until the power is turned on and the handle is in the down position. In the upright position the brush motor wont engage. Typical faults will be the belt is broken and needs replacing or the fornt brush motor needs replacing.

Nov 27, 2011 | Fantom Vacums Vacuums

1 Answer

Water won't spray out of the cleaner


If it won't dispense water then that means that the pump belt needs to be replaced. Here is the belt you need:

Bissell Proheat Pump Belt

May 22, 2010 | Bissell ProHeat Turbo Deep Cleaner Upright...

1 Answer

No water on carpet but apolstry cleaner will spray


Buy a cow... Literally. I did and it worked right when i bought it. My cow's name is Susie.

Jul 11, 2009 | Bissell ProHeat Turbo Deep Cleaner Upright...

1 Answer

I'm trying to find out how to install a drive belt in a kirby G4


I think this video that I shot should tell you everything you need to know about replacing the belt, and how to do basic maintenance on your vacum cleaners roller brush.

If you find the video helpful, please kindly rate it by clicking the thumbs up icon below;






Thanks for watching!


Chris

Apr 26, 2009 | Bissell ProHeat Turbo Deep Cleaner Upright...

1 Answer

Bissell pro heat washer


Most likely the belt is broke and the belt runs everything

Jan 12, 2009 | Bissell ProHeat Turbo Deep Cleaner Upright...

1 Answer

The belt is broken of my dirt devil


Remove brush roller and black caps at each end of the roller. Clean and oil the bearings.they must turn freely.

Dec 10, 2008 | Dirt Devil Vision Turbo W/Bonus Upright...

Not finding what you are looking for?
Vacuums Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

Roger Potts

Level 3 Expert

694 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...