Question about Hoover U6616-900 WindTunnel Bagless Upright Vacuum

1 Answer

Hoover only two years old an stopped working!

My hoover self propelled wind tunnel was working great until a couple of days ago when it started shutting on and off while vacuuming. I thought it was the outlet but when I plugged it into two different outlets it did the same thing. Then finally yesterday it just stopped working it won't even turn on when plugged in. I thought it was the switch but it is not. Is it the motor? Has the motor burned out? Do I need to buy a new one? Help!!

Posted by on

  • 1 more comment 
  • Anonymous Oct 29, 2008

    I have only had mine a couple of months and it is turning itself off it seems like it is getting hot.

  • Anonymous Jan 03, 2009

    I was just using it and emptied the cannister and when I went to turn on again, it just didn't switch on. I thought as clog might cause it but it wasn't that.

  • jimcarol Jan 03, 2009

    Just stooped working. Will not turn on again

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Legend:

    An expert who has written 200 answers of more than 400 characters.

  • Expert
  • 310 Answers

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=40540&thid=564949
Hoover only two years old and it stopped working!
Posted by baby_nurse on May 02, 2008
My Hoover self propelled wind tunnel was working great until a couple of days ago when it started shutting on and off while vacuuming. I thought it was the outlet but when I plugged it into two different outlets it did the same thing. Then finally yesterday it just stopped working it won't even turn on when plugged in. I thought it was the switch but it is not. Is it the motor? Has the motor burned out? Do I need to buy a new one? Help!!

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
Hoover U6616-900 Windtunnel Bagless Upright
I think you are right, if it is not the switch then it would be the motor. Does it smell bad like a burning smell? If so it is definitely the motor and then @ that point you may want to get an estimate for motor replacement, and keep in mind of what you spent on the vacuum versus what the cost of repair might be. My own rule of thumb is if it cost more than ½ of the price I paid for it then you have to decide – do I want to pay the repaired cost for the vacuum or do I want to purchase a new one. Just a suggestion... You may want to check with your local vac dealer. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.
http://www.hoover.com Telephone
Contact our Customer Service Department at 1.330.499.9499
Monday through Friday
8 a.m. - 7 p.m. EST

Don – The Vac Man
Go Ahead. Use Us.

Posted on May 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My hoover wind tunnel just quit while vacuuming. It is dead??? Two years old used about every other week? Any suggestions?


Some Wind Tunnels by Hoover have a poor design in the switch on the handle. Sometimes the switch does not turn on all the way and will stop running. Other times you can't turn the unit off.

Feb 28, 2015 | Hoover Self-Propelled WindTunnel Bagless...

1 Answer

Why won't hoover wind tunnel self-propel?


Hi there! The self-propelled feature is controlled by a belt. Check the belts on your Hoover Windtunnel by following these quick steps.

1. Recline the handle. Lay the cleaner fat and flip it over to expose nozzle base.
2. Remove the screws attaching the nozzle.
3. Check that the belts are not broken, stretched or damaged.

Replace the belts if they are damaged. Hope this helps!

Jul 04, 2014 | Hoover Vacuums

2 Answers

Self Propel doesn't work on Hoover Wind Tunnel


Your self propel wire could be broken. Lean the vacuum back like you were using it. If you stand in front of the vacuum look down and to your left. When you move the selp propel button you should see a wire move. If not then it's broken.

Oct 06, 2009 | Hoover Self-Propelled WindTunnel Bagless...

1 Answer

Hoover self-propelled wind tunnel doesn't self propel going backwards.


Your self propel cable sounds like you need to have an adjustment. reccomend a service shop repair.

Sep 25, 2009 | Hoover Vacuums

1 Answer

Why wont the self propelled brush on the hoover wind tunnel work. large belt is ok. the small belt looks 0k.


no don't do that,have a little patience.check where the self propelled assembly is and see if anything got in there,something might be loose and the teeth are meeting each other.thats a good vavuum.i have 2 but their not self propelled.try taking the belt off the self propelled machanisn and try it again.if it works then something is keeping the propelled machanism from working.dig a little deeper,what do you have to lose?

Mar 24, 2009 | Hoover U6437-900 / U6439-900 Windtunnel...

3 Answers

Hoover wind tunnel upright self propelled. U6473-900. Brush does not work. Heard it was a 'brush controller' problem and can be fixed. Please tell me how.


Most likely the flat belt has stretched enough so as to not turn the pulley that in turn turns the brush roll using a V belt. Also there is a small idler wheel, if hook up, then it won't engage the V belt.

May 20, 2008 | Hoover Self-Propelled WindTunnel Bagless...

1 Answer

HOW DO I REPLACE THE DRIVE BELT ON A HOOVER WIND TUNNEL SELF PROPELLED


Take the brush belt and slip it over the pull into the groove. Then take the flat belt and hook onto the motor shaft and then pull belt over pull and push it around the entire pulley. It can be difficult but after the first time it is easy. You have to push the belt up with your thumbs so the belt will wrap all the way around

Apr 06, 2008 | Hoover Company Wind Tunnel U53019 Upright...

1 Answer

Repplacing power cord on Hoover Wind tunnel (not self propelled)


Hi
This is HARD and you NEED electrical knowledge and IF NOT UP TO IT YOU COULD CAUSE PROBLEMS TO YOUR SELF AND OTHERS.
You do not say what the problem is with the cord.If is it damaged then it needs to be replaced with a new one.and then above applies.
Take Care as to what you do.
SAFETY FIRST---ALWAYS
Hope this helps
Jay

Nov 17, 2007 | Hoover U6437-900 / U6439-900 Windtunnel...

Not finding what you are looking for?
Hoover U6616-900 WindTunnel Bagless Upright Vacuum Logo

1,052 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

Roger Potts

Level 3 Expert

694 Answers

Ryan S
Ryan S

Level 2 Expert

328 Answers

Are you a Hoover Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...