Question about Jackson 25 in. Conserver XL Free-standing Dishwasher

1 Answer

Where can I get a replacement drum switch ??

The little plastic wheels on the drum switch have broken, can I get replacement wheels or the whole drum switch. it's a 6 position switch with the first and 3rd wheels are fixed. the other 4 can be adjusted, all are no/nc switches

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 38 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi- my dishwasher - single drawer fisher and paykel seems to be stuck on runners- will not open smoothly


this could be a broken wheel or something jamed inside the runner, theres a little plastic clip that is on the end of each runner remove the clips and pull the basket all the way out then check for broken wheels or something jaming it, or even a twisted runner. be carefull removing the clips as they can snap. Ps carefull of sharp edges too.

Jan 20, 2010 | Dishwashers

3 Answers

The handle on my Maytag Quiet series 100


I had the same problem with my QS 100. I disconnected power first via the breaker then removed the 11 screws. I couldn't loosen the two electrical connections, but the door pulled far enough away to inspect the handle mechanism. The plastic handle fell out of whole handle assembly rather easily because two molded plastic pins protuding from either side had broken off and were loose inside. There was also a pair of molded plastic v-shaped forks right on the panel to hold the handle assembly and these were damaged but they just to seem to act as guides only (as the handle assembly is held in by two of the screws that were removed). Replacing the v-shaped forks would require a whole new door which I am NOT doing. It looks like I can a replacement handle in the same color with new pins (I am reading they may now be metal) for about ##15. Pretty easy to disassemble and inspect, only about 15 minutes.

May 29, 2009 | Maytag 24 in. MDB5600A Jetclean II...

1 Answer

The upper sprayer arm fell off on my Frigidaire FDBB4365FC0.


I just had the same thing happen and fixed it! You might need to remove the upper rack first. In the "Roof" of the dishwasher, you should see what looks like a plastic gear wheel. It will screw off, but you will need to put a little force to get it started. Inside of the gear is a free floating plastic ring with 2 small teeth on one side. Make sure the teeth are facing down through the center hole of the wheel. Hold the ring with one finger, and snap the spray arm back in place. Just screw the assembly back into the washer and all is good... Until it falls out again...

Mar 21, 2009 | Frigidaire PLD4375RFC Dishwasher

1 Answer

The flimsy plastic guide wheels on the rack for my (ca. 2000) GE monogram dishwasher have been breaking. Six so far. GE wants $25 - $30 per wheel to replace and $235 for a whole new rack!! I will not...


We have just solved the problem with our wheels falling off! For .75 cents a wheel we purchased new wheel "clips". The connect straight into the wheel instead of "rotating" on. Big differnence and so easy to change out! 5 minutes and the problem is gone. The item number is WD12X10277 and it is a GE product. Hope this helps!

Mar 14, 2009 | Dishwashers

1 Answer

Loud Dry Bearing sound


Warning! To avoid personal injury or even death, always disconnect your appliance from its power source--that is, unplug it or break the connection at the circuit breaker or fuse box--before you do any troubleshooting or repair work on your appliance. Also, because some components may have sharp edges, use caution while working on your appliance.
If your dryer is noisy, check these:

Rollers
Idler pulley
Glides
Rear drum bearing
Blower wheel
Rollers Many dryers use rollers or wheels to support the clothes drum. When these rollers are worn, they can be noisy. You should replace the whole set of rollers at the same time.

Idler pulley Dryers have a tension or idler pulley that keeps tension on the main drive belt. When it's worn, it can be noisy. When that happens, don't lubricate it. Just replace it.

Glides Many dryers use nylon or plastic glides at the front of the clothes drum for support. When these are worn, they can be noisy. When that happens, replace them.

Rear drum bearing Some dryers support the clothes drum in the rear with a center spindle instead of rollers. The spindle may be a ball-and-socket type support or a shaft through a sleeve. When the components are worn, they may squeak, squeal, or rub. You can't repair them. Just replace them when they're worn.

Blower wheel Your dryer's blower wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. The blower wheel, which is usually plastic, may wear out over time. But if it's noisy, it may simply be clogged with lint. Clean the blower and test to see if the dryer is still noisy. If it is, you probably need to replace it.
If my assistance helped resolve this issue, please show your appreciation by rating how effective my advice was in resolving this issue.
Thank you,
Dave E. (Illeagle)

"Your satisfaction is my personal reward"

Jun 23, 2008 | Fisher Dishwashers

9 Answers

GE dishwasher nautilus - bottom tray caster wheels come off daily.


I finally found a solution after 2 years! Appliancezone.com has wheels and studs to fix problem. WD12x10136 and wd12x10277. About $17.00 and rack is rolling perfectly. GE wanted 200 for an entire rack, no thank you!

Apr 06, 2008 | Danby DDW1805W Designer Series...

3 Answers

Broken casters (wheels)


This is definitely something that you can do yourself. Remove the back of the dishwasher and the front kickplate. This will give you access to the wheels. The wheels are held in place with a U shaped clip. Remove the clip and the wheel will come out. replace with the new wheel.

This happened with my Danby DDW1805 and I fixed it myself. I used two step stools at the side of the dishwasher to raise it off of the floor.

Aug 28, 2006 | Danby DDW1805W Designer Series...

Not finding what you are looking for?
Jackson 25 in. Conserver XL Free-standing Dishwasher Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jackson Dishwashers Experts

yadayada
yadayada

Level 3 Expert

60639 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Peter Hampton

Level 2 Expert

193 Answers

Are you a Jackson Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...