Question about Linksys Wireless-G WRT54G Router

1 Answer

LINKSYS STOPED WORKING - Linksys Wireless-G WRT54G Router

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 156 Answers

Take a pin and push the tiny reset in...hold in for 10 seconds... Also reset your Cable/DSL modem if you have one and wait for a few minutes.

Posted on May 02, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My linksys wireless 802.11 g has stoped working. first i lost my secure wirelesss and then the linksys wire function. I have turn off and on on the linksys, but no connection and my home secured...


To reset the Linksys back to the default settings - Press and hold the pinhole RESET button at the back of therouter with the power ON for 20 secs. then release the RESET button.
To connect to your wireless router, the router's wireless settings needs to beconfigured with the SSID, encryption etc. and also the wireless cards in allthe laptops/computers needs to be configured with these router's wirelesssettings. Then the laptops/desktop computers can communicate with your wirelessrouter.
Connect a LAN cable from the Linksys to the LAN port on your computer.
Open a browser and enter the Linksys configuration URL
http://192.168.1.1
The default login = admin
The default PW = admin
You can protect your router by changing the default admin PW (write it down andput it in a safe place)
Go to the wireless configuration and set up the SSID and WPA or WPA2encryption.
Apply these settings to the wireless card in your laptop/computer.

To secure your wireless network from unauthorized access, please click on thislink and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Sep 10, 2011 | Linksys WIRELESS-G WRT54GS 802.11G...

1 Answer

I have a linsys pap2 and it's all 4 lights are blinking continously for 4-5 times and then stoping and then again blinking and stoping so i wanna know the solution.


there was a problem with you lynksys router.. first try to unplug your router for atleast 5 mins.then plug it again. if the problem still in there. you need to purchase a new lynksys router.router cannot be repair technically..

Jun 07, 2011 | Linksys PAP2T

1 Answer

Linksys wrt3500n router firmware load problem after I try to update it stoped in the middle now I can't get in


If inserting a straighted Norwegian paper-clip into the small "reset" hole in the back of the router does not reset the router to its "factory" settings, then the router has transmogrified itself into a door-stop-brick, and must be replaced. If it's still under warranty, Linksys may replace it.

Jan 16, 2010 | Linksys WRT350N Wireless Router

1 Answer

Linksys rouder suddenly stoped alowing other computers net access


I would recommend upgrading the router firmware, if you have not done this already.

Download the firmware file from the Linksys website:
http://www.linksysbycisco.com/US/en/support/

Typically, the upgrade is done by pointing your web browser at the IP address of the Linksys router. Linksys should provide specific instructions at the site above.

Nov 01, 2009 | Linksys Wireless-G Broadband Router

1 Answer

I dont know how to change NAT type.


since NAT has to be set on the Linksys...
you will have to use the software provided by linksys, or use a web based interface which connects to the linksys and you can do the respective changes...!!!

Jan 28, 2009 | Linksys WRT54GX2 Wireless-G Broadband...

1 Answer

Built in wireless not working or showing up


Assuming that you have a Linksys wireless router, go to Start>Run then type 'http://192.168.1.1' and Enter. A logon window will appear. Use 'linksys' for the user name and 'admin' for the password. Now you should be looking at the Linksys configuration utility which will show your status. If you are using cable select DHCP for protocol, if DSL use PPPoE. good luck, Steve Medley

Oct 28, 2008 | Toshiba Satellite A105 Notebook

1 Answer

Linksys WRT150N


There is always a wireless option on your router. Check to make sure that your wireless is turned on and that you arent blocking your wireless signal with a WPA personal passcode.

Apr 10, 2008 | Linksys Wireless-N WRT150N Router

Not finding what you are looking for?
Linksys Wireless-G WRT54G Router Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18357 Answers

mark

Level 2 Expert

105 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...