Question about E-Machines eMachines Monitor E15T4

2 Answers

Monitor blinks no image

All of a sudden my monitor went off and started blinking. when it blinks it shows the image that is supposed to show if it could be seen. in the mean time it blinks and shows nothing. can it be fixed?

Posted by on

  • texasgal007 May 14, 2008

    my computer screen blinks on and off...I have tried to shut down and restart. I have also tried to mess with the plugs and make sure its all plugged in. Do you know how to fix my computer?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My computer screen blinks on and off...I have tried to shut down and restart. I have also tried to mess with the plugs and make sure its all plugged in. Do you know how to fix the problem

Posted on May 17, 2011

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

First you need to isolate the problem to either the computer or the moniter. I would sugust that you hook a know good moniter to the compter and go from there. If the other moniter works then you have a moniter issue aif not chek the video card in the computer. good luck
budman630

Posted on May 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My LG screen is suddenly blacking out, both during the boot-up process & durin gnormal use. If I turn it off & back on again, it shows a normal screen, then suddenly blacks out again. It is just...


That would be your backlight failing on you. Very common on anything with a lcd display. It will be covered under warrenty so check that. Also make sure you know what a replacement screen is worth as it might cost as much as a new monitor to fix, the parts are cheap but the labor isn't.

It will probably blink out more and more and then fail totally. The lcd itself is still showing the picture but without the backlight you can't see it other than perhaps a ghost image at an angle. There are replacement/repair kits for the backlight power board (if that model has a seperate board) and replacement lamps. You can do this as a diy fix with a little care and a few jewlerrs screw drivers and such tools.

Mar 28, 2010 | LG 22" FLATRON LCD Monitor

1 Answer

Samsung 56V, difficult to switch on the monitor


check the capacitors inside the monitor, as they may be broken, and they start screen up, just change em and it should kickstart fine

Sep 19, 2009 | SAMTRON 55V 15" CRT Monitor

1 Answer

Monitor goes black............


try checking the cables first.

May 28, 2009 | Dell E176FP 17" LCD Monitor

1 Answer

Syncmaster 2232gw led blinking.


Change the screen resolution. The video card or video display may not be compatible to the supported video setting of the monitor. Try changing the video resolution to a lower setting such as 1024x768 and bit depth to 32 bit.

Mar 15, 2009 | Computer Monitors

1 Answer

ViewSonc VX924 LCD Monitor


Check the information at Viewsonic's website regarding their warranty:

http://www.viewsonic.com/support/warranties/limited-warranty/

If you have your proof-of-purchase and it shows the monitor is less than a year old, it would be covered. You would need to follow the procedure on their website to have the unit repaired or replaced, but it would not be your job to try to fix it.

Feb 11, 2009 | ViewSonic VX910 19" LCD Monitor

1 Answer

Blinking blue light


You have to check if you can see the image on the screen or not after it went blank (Power on both CPU and monitor) by shining a flashlight into the screen, not directly but find the best angle to the screen and take a look very closely. If you can see the icons or any image, there will be a minor problem. Like mine, I can see window image using flashlight and check lamps inside. Some of them were broken and it is very easy to replace. If you cannot see anything on the screen, there'll be some problems with inverter board. If you have soldering tool and want to fix it by yourself, check the caps first. It may cause this problem. Some caps might show leaking or burn spot on the board because of too high temp. If you don't have soldering tool, you better go get a technician to do so.
Thank you

Mar 12, 2008 | Samsung SyncMaster 930B 19" LCD Flat Panel...

1 Answer

Monitor Went Black


It sounds like the monitor might be going bad. I would try hooking up another computer to it. If it works with another computer, then I would say the Video card might be going bad.

Mar 01, 2008 | Dell E173FP 17" LCD Flat Panel Monitor

Not finding what you are looking for?
E-Machines eMachines Monitor E15T4 Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top E-Machines Computer Monitors Experts

buzz flewhart
buzz flewhart

Level 3 Expert

655 Answers

Ricky Ostrom
Ricky Ostrom

Level 2 Expert

270 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you an E-Machines Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...