Question about Multimedia Projectors

1 Answer

Preylahong NEC MT830+need help to reset new lamp

Hello,
Marrie if you can help me out am trying to put new lamp on my MT830+ NEC projector but I don't know how to reset lamp please help thank you.

Posted by on

  • 00700 Jun 27, 2008

    hello !

    i want to reset my toshiba tlp-s10 after lamp changing.

    what must i do ?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

After replacing lamp in MT-830(NEC) press and hold "on" button for 10 seconds to reset lamp hours. If projector has beyond 2100 hours press the "off" button for 10 second.

Posted on May 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lamp hour reset NEC MT1060


The NEC MT1060 lamp hours is stored in an EEPROM chip built into the lamp. As soon as you put in a new lamp (MT60LP or MT60LPS), the hours will be reset. If you remove and put back in an old lamp, the unit will see the hours on that lamp. Thus if the lamp has reached 2100 hours, the projector will remain in standby. See page 53 of the manual for the replacement and reset information.

Most of the manuals for the NEC projectors are available here: http://www.nec-display.com/dl/en/pj_manual/lineup.html . The direct link to the manual for the MT1060 is http://www.nec-display.com/dl/en/pj_manual/mt1065.html .

I hope this helps.

Cindy Wells

May 24, 2016 | NEC MT1060 Multimedia Projector

1 Answer

How do I reset my nec projector model vt700 lamp time without remote


How to Reset a NEC Projector Lamp Timer ... - RelampIt

www.relampit.com/Projector-Lamp-Timer/NEC-Projector-Lamp.php
How to Reset a NEC Projector Lamp Timer. Make sure the projector is in standby mode; Press the Off or Help button on the remote control for a minimum of 10 ...

NEC reset lamp without remote Questions & Answers - Fixya

www.fixya.com/tags/reset_lamp_without_remote/browse/nec
My bulb warning had just recently appeared a few weeks prior, so I thought the bulbmust ... ...reset the Lamp timer o an NEC MT1050 projector. ... ...reset lamp usagetime without the remote on NEC VT490 HelloPress the MENU button on the ...

reset lamp hours nec projector without remote Questions ...

www.fixya.com > Forum > Tags
Find solutions to your reset lamp hours nec projector without remote question. ... My nec vt48 projector gets hot and turns off. It ... Question about VT700 Projector.

Replacing The Lamp - Nec VT700 User Manual [Page 58]

www.manualslib.com > ... > Projector > VT700 > User manual

Jan 29, 2016 | NEC Multimedia Projectors

2 Answers

VT595 LCD Won't come on. Power light orange Status red Blincks Once every sec or so.


If the lamp life has exceded its safe working limit, it will probably go into a permanent standby mode, I used to have an NEC MT830, I had to hold down the off button for 20 seconds to reset the lamp life, maybe it will be something similar. If you have your manual, it may give instructions, if not there will be a downloadable manual on the NEC website.

Good luck

Aug 09, 2011 | NEC VT595 LCD Projector

1 Answer

Need the projector bulb where can i get it and how much multisync mt830


Hello I am an electronics technician from Washington,DC. Try projectorzone.com they are located in Portland,Oregon I have used them several times. Nate was very helpful. You can find a lamp there for sure.

Nov 19, 2010 | NEC MultiSync MT830 Multimedia Projector

1 Answer

Nec mt-1065 lamp hours reset


Hello, unfortunately the NEC MT1060 - MT1070 series projectors have EEPROM chips built into the lamp housing which counts the hours that the lamp has been used for so the only way to reset the hours is to change the lamp for a new one, i have not yet found a way to reset the chips even by reprogramming them, i'm afraid the only solution is to replace the lamp with an official NEC unit, but this was obviously their intention.

Oct 25, 2010 | NEC MultiSync MT1065 Multimedia Projector

1 Answer

How to reset Time clock on NEC MT830+ Projector


change the lamp even if the old lamp

use original nec remote contro

l6. After you install a new lamp, select the lamp Usage icon and press and hold
the "Power On" button on the remote control for ten seconds to reset the
lamp time clock to zero.
NOTE: If resetting the lamp clock back to zero after 2100 hours of service,
press the "Power Off" (not "Power On") button on the remote control for ten
seconds

Sep 20, 2008 | NEC MultiSync MT830 Multimedia Projector

4 Answers

Lamp Timer Reset...


Hello, does any1 know how to reset the lamp timer on a LG RD-JT31? I want to get rid of the Replace The Lamp sign.

Regards Linus

May 12, 2008 | Multimedia Projectors

1 Answer

Nec mt 1000


go to menu- go to setting -go to colour move slider to right hand direction befor you change the lamp -take care that some vga cabel(((cabel between pc and projector make this fault).then you have to change this cabel and try.

Mar 09, 2008 | NEC MultiSync MT830 Multimedia Projector

2 Answers

NEC Projector


they have a fuse on the power board inside the projector itself, But normally the fuse does not go bad unless their is a dead short in the unit.

Dec 13, 2007 | NEC MultiSync MT830 Multimedia Projector

5 Answers

Blinking bulb light


Hi there

You must always reset the lamp timer when replacing a bulb.

Dec 11, 2007 | Dream Vision CINEXONE Multimedia Projector

Not finding what you are looking for?
Multimedia Projectors Logo

Related Topics:

743 people viewed this question

Ask a Question

Usually answered in minutes!

Top Multimedia Projectors Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

The Knight
The Knight

Level 3 Expert

68352 Answers

Are you a Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...