Question about Projection Televisions

1 Answer

32 lcd flat screen

Ok what's the fix and what do think the cost is

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 1,894 Answers

Oh u posted the request here huh?
i was lookin into the premium request.
ok here you go..
Technically speaking, there is no such thing as "ghosting" on digital
Ghosting might visualy describe it, but if you're not watching analog then that's not the problem. The problem is most likely in the convergence.
First thing first - If still under warranty or if you have no electronic repair experience you should take the set back to the shop or to a repair person. Some of the solutions described below can be dangerous, TV's are very hazardous to service.
If you don't have any repair experience my suggestions can only be usefull to get a repair estimate, or in order to get more familiar with these kind of problems, impress your local repair person etc..
actually tat effect wil be in some red colour..(assuming tat its of red colour).. ur case is with green.. but i shall say u in red.. u just convert it..

switch to test mode to check the red crosshair compared to the green or blue - if it seems out of focus, open the set and mark the position of the lense. Then adjust it to tighten the line.
Find out why the Red has shiffted(pin trouble). look for bad solder joints on that board. Its also Possible that you have a failed component
Try resoldering the STK Output IC's very carefully. In a worst case scenario , you may need to change the STK that controls the Red Convergence .
Yank out the convergence board(the one that has several controls) on it, then you will find a few contols that have RED PIN (whatever). on them. Adjust them untill you get it right

problem solved.

Posted on May 02, 2008

  • dewan nafees ahmed May 02, 2008

    cost may vary with the place u live in... so confirm it with the local electronics shop by taking the failed components to him..

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 32 LCD TV will not turn on without been turned on and off many times. The power lights come on butte screen is black .


O O, it sounds like your power board is going out have a service man come out and tell you whats wrong it cost $600 for the part I just bought another flat screen its cheaper. Good luck

Jul 01, 2014 | Sony Grand WEGA KDF-60XS955 60" Rear...

3 Answers

Screen hit by an object


do you have any crack on the screen?

Jun 30, 2008 | Projection Televisions

1 Answer

Toshiba TP55D80 rear projection has sunburn


nope...get a new one, my call..unless you like to do this a lot..

Mar 11, 2008 | Projection Televisions

1 Answer

Made popping sound, no picture but, sound ok. makes noise when trying to change channels.


I keep seeing this kind of problems with lcd and other flat screen tv's

In order for a lcd, plasma, or dlp screen to power up, it requires a quick start system, and it uses capacitors to achieve this
Those capacitors are fragile, and all it takes is a quick on off on again, and ...pop!

The capacitors are more than likely blown. If your t.v. is under warranty, I would take it to the place you bought it for repairs, as this can be an expensive repair job.
Depending on how many of the capacitors failed, if could cost almost as much as the tv itself to fix it.

Dec 14, 2010 | Mitsubishi WD-57733 57" HDTV

1 Answer

I dropped my Samsung flat screen TV and the inside screen is broken. Can this be repaired?


No, it cannot be fixed.

The part is called a display panel and even if it is available the cost of such a part is more than the set cost when new.

LCD AND Plasma panels are very fragile.

SD TECH

Oct 27, 2009 | Hitachi 65F59 65" HDTV

1 Answer

Need new lcd screen for 32" sylvania


I am not aware of replacing just the front screen, that is the LCD display and is most likely more than the set cost. Please be very careful when purchasing something like this on e-bay. I can't see how they will have a display for such a new set. Can you give me a model number and I will do the homework for you?

Feb 13, 2009 | Mitsubishi VS-6043 60" Rear Projection...

1 Answer

32 in. LCD Flat Screen Blank Screen


Is it under warrentee?
It sounds like the main fuse inside blew. Does the outlet work at all?
If not, reset the circuit breaker or if it is on a power strip, reset the strip trip switch.
Mastersage....................

Feb 08, 2009 | Philips Magnavox 51MP392H Rear Projection...

1 Answer

32" Panasonic Flat Screen - wont power up.


I think that if all the fuses are ok then the problem is on the power supply board. If you can check this for yourself otherwise find a qualified technician. Hope this helps.

Jan 18, 2009 | Projection Televisions

1 Answer

Sony kf50sx


problem can be fixed for under 500.00

May 30, 2008 | Sony KP-51HW40 51" Rear Projection...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...