Question about Projection Televisions

2 Answers

Coby tv model # tf-tv3005 ballast circuit module bad, where can I buy Parts

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 124 Answers

Hi, I am just checking to see if you were able to the the unit fixed. If not, I need parts. Thanks

Posted on Oct 27, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 549 Answers

The best I can do is give you this link.
or

http://www.mouser.com/Search/Refine.aspx?FS=TRUE&Ntt=*ballast*+*control*&N=1323038&Ntx=mode%2bmatchall&Ns=P_SField&OriginalKeyword=+ballast+control&Ntk=Mouser_Wildcards

http://www.MouserElectronics.com has some in stock, but I so not know your part number.
If it is not listed and you call them, they normally are good at locating a part.

Posted on May 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was told I need a new lamp ballast assembly. I was also told by someone to order 6913V00002C Ballast (EUC 100 P/11) but when I opened my TV and took out the "bad" ballast, its is a EUC 100 C/00. Anybody...


so the one first is an LG model ballast but the one in the tv is a phillips one, strange.. can you give me the bord number power side... it is always best to replace old number so the damaged numer one should be the number you use. LG, Philips etc use different part to make the same tv model. e.g one can be made in twain and the other from china. both the same case do the same things but have completely different parts in side. Looking at the parts on line they don't have the same connections or the same voltage so would be a bad idea to try and put the new one in with the wrong number.

Oct 22, 2013 | LG RU-60SZ30 60" Rear Projection...

4 Answers

Repeated temporary lost picture


the problem on your tv is in the IF circuit as you had mention that it lose sound and picture but not power take it back to the work shop and tell them to run through the IF circuit it is faulty.good luck.

Jun 07, 2007 | RCA HDLP50W151 50" Rear Projection HDTV

2 Answers

My 50in LCD has had a green tint to it for several months, was told by Best Buy that it was likely that a mirror got misaligned when we moved. Friend had the exact same tv...thought that the bulb went...


Good luck with that.... But if you really want to try,... look at where the bulb makes electrical connection when it is plugged into the set. You should see two thick wires leaving a connector and going to a circuit board. this board is the ballast. You'll have to disassemble until you can get the board along with the wires and connector.

Aug 14, 2010 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

Intermittent picture. Lights on circuit blink when starting up. Often sound, no pic. Blue and blinking yellow for 2 or 3 tries, then picture. Sometimes only blue with no sound or pic. Ballast?


Ballast Board! Go to Encompass Parts Distr online find out what your Part# is! or Call 1-800-638-3328 also try UED 1-800-648-6657 This TV has alot of fuses over 20 of them!You didnt say have you replaced Lamp thats what goes first 9/10 unless you get power surge or Bad capacitors on the power supply Board caps are bad if they are puffed up on top 1000uf25v caps!

Nov 23, 2009 | Toshiba 56HMX195 52" HDTV DLP Projection...

1 Answer

TV keeps turning itself off, how to stop this? Thank you


CK all of your Fans and you may have Bad Ballast Board. But Start with fans if they stop running set will turn off also go to Encompas Parts online look up your Model Number or call them 1-80-638-3328 and you could have defective Lamp if Lamp has never been replaced and all fans are running then its the Lamp! If Lamp does not come on its the Ballast or Bad Fans.

Nov 23, 2009 | Samsung HL-S5087W DLP TV

1 Answer

Programming our dish network remote control. We do not have the remote code for our new Coby MODEL: TF-TV2214


1. Turn on your TV. 2.Press & hold the TV Mode button until all Mode buttons        light up. 3.Press red power button 4.Press the UP ARROW repeatedly (about 1 press per second) until your TV turns off. 5.Press # POUND The TV Mode button will flash three        times. 6. Press the POWER button to turn the TV on and try other buttons to make sure the code works. If you want to try another code, start over from step 1.
Below is the website for the online manual which will give further instructions.  
http://dishnetwork.com/downloads/pdf/user_guides_and_manuals/remotes/6_3_RemoteManual.pdf

In looking at the manual no codes are given for the Coby brand TV. If the above process does not work, you'll have to call DishNetwork for further assistance. It may be that the remote will not work for your TV.

Dec 06, 2008 | Projection Televisions

1 Answer

Samsung dlp tv no picture


Sure, you can test by Use the screwdriver and remove the protective cover that conceals the ballast.

Observe the ballast before proceeding. If oil is leaking from the ballast, stop here and remove the ballast. Leaking oil indicates that the ballast is damaged beyond any doubt as the internal seal has been ruptured by excessive heat.

Test the high voltage side for continuity between the wires going to the ballast tombstones. There will be either one or two wires going to each tombstone fixture. Regardless of the number of wires, the colors will be the following: Blue or yellow are the power wires and white is the common or neutral wire. this could differ in many models.

Turn the Volt Ohmmeter to "ohms" and touch the ends of the two probes together. The meter should show continuity or a direct short. Touch the probes of the meter to one of the white wires and one of the colored, blue or yellow, or any wires that comes from the ballast. This should show a short or continuous circuit. If it does not, the ballast is bad and should be replaced.

Oct 01, 2008 | Samsung HLM507W 50" Rear Projection HDTV

1 Answer

Zenith E44W46LCD


Yes you could be missing your 300v to the ballast or you could have a bad ballast in any case this set is very difficult to disassemble be careful

Jun 10, 2008 | Projection Televisions

2 Answers

2006 42'' Samsung rear projection, Balist????


A Ballast is a circuit that provides voltage to Lamp. Ballasts are only used with TV's with a Lamp. According to your model number this unit does not use a lamp. That model number uses 3 rear-projected CRTs. The most common units with a ballast would be a DLP HDTV.

The Model number you specified HCN4226W is a unit made in 2003. However you stated in your subject line that this was a Samsung unit from 2006. Please verify your model number.

Feb 29, 2008 | Samsung HCN4226W 42" Rear Projection...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...