Question about Denon AVR-1601 Receiver

1 Answer

Denon avr 1601 amp

Can i use a 500 watt speakers for it

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 979 Answers

Yes, although there may be an efficiency factor involved...accordianman

Posted on May 01, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blinking standby light on Denon


could be a couple things. Either a blown channel in the amp, or a bad voltage regulator. would have to investigate further with a meter to find out.

Aug 27, 2014 | Denon AVR-1601 Receiver

1 Answer

Service manual


http://www.smpcshop.com/Denon-AVR-1601-AVR-681-Service-Manual.html

Sep 11, 2013 | Denon AVR-1601 Receiver

1 Answer

I need too know how to hook my speakers up to my DENON AVR-1601


Check the User Manual, at the site on FixYa:
http://www.fixya.com/support/p41782-denon_avr_1601_5_1_channels_receiver/manual-18165
Very easy instructions, I hope this helps.

Feb 06, 2012 | Denon AVR-1601 Receiver

1 Answer

What is the button combination to reset the Denon AVR-1601 to factory presets?


switch off, then hold A and B speakers, then switch on and hold about 3 seconds. This is reset to factory defaults.

Jul 22, 2011 | Denon AVR-1601 Receiver

2 Answers

Unit turns on for about 5 seconds and turns off with stand by light flashing


you have shorted output transistors which is causing the unit to go into protect mode. You can try factory reset by turning off unit then holding down speaker a and b buttons then turning back on.

Apr 12, 2010 | Denon AVR-681 Receiver

1 Answer

Manul denon avr-1601 en castellano


http://www.usa.denon.com/ArchivedAVReceivers.asp?archivedModelSearch=true&clearCurrent=true&archivedCategory=AV&archivedModel=AVR-1601&imageField.x=15&imageField.y=13

Espagnol as well ...I think

Dec 12, 2008 | Denon AVR-1601 Receiver

2 Answers

Denon AVR-1601


This is a very common problem with denon receivers of the 2001-2-3 vintage. On almost every one, there are 4 little "surge" resistors in the power supply. These werent quite robust enough from the factory and one day would just burn open for no reason. Well, actually there is a reason, the "surge" that happens every time you power the unit up eventually weakens the resistors and then they pop. You need to take this to a denon service shop as I GUARANTEE they have seen this before. They need to check resistors in the picture, locarde above the **** rectangular connector. Resistors numbers R141, 142, 148, 149: 75f69d7.jpg These resistors when measured, should be less than 10 ohms each. If they are more, then they are blown. If they are blown, then have the shop check the channels for blown output transistors. If the outputs are OK, then these resistors should be replaced with 1 ohm 1/2 watt metal -film flameproof resistors. You might need to be prepared for a large bill, because the entire unit must come apart to replace the resistors, however, just checking them takes only about 10 minutes... Good luck and don't try this at home. Rob

Apr 08, 2008 | Denon AVR-1601 Receiver

1 Answer

Denon 1601 avr


The unit is in protect mode. It has detected a problem in the final output stage and has shut down to prevent further damage. Disconnect the speakers completely and try turning it on. If you still get the same symptom, the problem is inside the unit and repair is required. Usually when this occurs, the output transistors have failed. There will be at least 2 that need to be replaced. Figure on parts costing around $15-$25. Add in the local labor rate for the complete repair cost.
Dan

Apr 07, 2008 | Denon AVR-1601 Receiver

1 Answer

Denon AVR-1601 Receiver


Check capacitors in power supply......also check for over-heated
resistors..all 1 ohm.....replace if cooked...................T.

Nov 21, 2007 | Denon AVR-1601 Receiver

4 Answers

Avr receiver


More than likely audio o/p problem.could be speaker problem,dissconnect speakers and try to power on if still no go it is job for technician.If it works one of your speakers has a short on it,good luck

May 14, 2007 | Denon AVR-1601 Receiver

Not finding what you are looking for?
Denon AVR-1601 Receiver Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Denon Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

4861 Answers

Dennis McCollum

Level 2 Expert

137 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Denon Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...