Question about Dishwashers

1 Answer

Hobart lx 30 pump seal

Need service manual for pump seal replacement

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

May have a leak on water pump. Where could it be coming from.

Posted on Aug 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need bushing for sprayarm and repair manual


The wash arm bushing for this model is not available separately. You can use the bushing from the LX series and cut it shorter to length. Hobart will not issue service manuals to non Hobart personel because of liability issues. If you injured yourself from misinterpreting the manual, they would apparently be resonsnsible.

Dec 08, 2013 | Hobart SR24-H Built-in Dishwasher

1 Answer

Hobart LX 30 undercounter dishwasher, commercial Does this model require booster?


Most of the Hobart LX series of dishwashers have their own built-in booster heaters. To check for one, remove the lower front panel (2 screws). The booster heater, if present, will be a stainless steel tank on the left side. If it doesn't have a built in booster heater then it was meant to be used with chemical sanitizer instead.

Jun 29, 2011 | Hobart 24 in. LXIH-3 Built-in Dishwasher

2 Answers

I have a LX40 and need parts list . I have a valve or solinoid that is leaking on upper back of machine


i have an lx 30
i think its called a breaker fill valve
hobart sells a rebuild kit thats pretty easy
1str unscrew 2 screws that hold cap on and save
with pair of plyers or channel locks unscrew top where 2 screws were screwed into,counterclockwise,
should be a plastic plunger, with rubber seal, rermove and replace with new one from kit, use grease to grease shaft
re enstal.
make sure you have kit before you attempt this.
if you have hard water deposits, clean those areas best you can,on top nut, also if your lx has a booster heater, hard water will cause havic and expensive repairs, a water softner from the yellow pages , will be your lx s best friend, and their not expensive

Jul 15, 2009 | Dishwashers

2 Answers

Hobart LX 30 P2 Error and unit overflowing!


Hi drogers77,

I'm not a Hobart technician, but here what I founded in my manual for the LX30 error message:

LX18 / LX30 display shows E0, E2, E3 or E4

1. Low water pressure - check for clogged hose strainer; check that site water pressure meets minimum flow pressures.

2. Make sure probes are clean

3. No water pressure - main water supply valves may not be working

4. Drain valve open - turn machine OFF to drain machine, then ON. Repeat twice (this assists in clearing any drain valve obstructions). Wait for machine to reach READY mode and press WASH. Slowly open door several seconds later and note water level. Close door; 30 seconds later, open door slowly and check that water level is the same as it was. If not, repeat the OFF-ON procedure. If problem persists, call your local Hobart Service Office.

5. Delime machine.

Hope it will help you.

pepsicrazy

Dec 27, 2008 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Lx 30 h hobart dishwasher


I hd the same problem. water was boiling during even when the machine was not washing. I replaced the temperature probe located inside the sump, and the problem was solved.

Aug 17, 2008 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Hobart lx 30 pump seal


can you provide a serial number please?

Apr 30, 2008 | Dishwashers

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

328 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...