Question about Fisher and Paykel GWL11 Top Load Washer

1 Answer

Aquasmart too many suds

I have been washing well for ages and now there is too many suds in the bowl and it is not spinning the clothes properly. I have tried the clean me function and re rising. Is there a way of draining the water froom the bottom of the machine to get rid of the excess suds and water?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 487 Answers

Means that the pump might be blocked and not drains too well
Please check this link for all drawings and or perts you might need. Please clean pump out first

LINK

Posted on May 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Aquasmart bowl not turning freely, problem with stator assembly?


Hi your shaft may be bent,Or metal particles on the rotor magnets.
Get someone to turn the bowl & you look at the shaft without the rotor on & see if it's bent.

Jan 09, 2013 | Fisher and Paykel Aquasmart wl80t65c

1 Answer

Continues to go out of balance


The stainless steel bowl has lost its ballast water & goes out of balance,Replace faulty bowl.

Oct 03, 2012 | Fisher Paykel Fisher & Paykel AquaSmart...

1 Answer

What is fault 40


Fault code 40 info
40. (00101000) Bowl Dis-engage Fault
While carrying out a bowl check, the Motor Control Module has found that the bowl is not
engaged even though the pressure sensor indicates that the bowl is empty. The Motor
Control Module continues to check for 2 minutes, after which time it displays this fault. The
first two areas to check are the clutch and the pressure tube. If these two appear correct,
then the fault could be in the pressure sensor in the Motor Control Module.
Primary Source: Mechanical.
Action: 1) Check that there are no clothes or other foreign objects preventing
the clutch from re-engaging. Excessive suds can stop the bowl
rotating.
2) If the machine is empty of water, carry out a clutch disassembly
procedure and check the spline drive.
3) Next check that the pressure tube has not come off and that it is
not kinked.
Secondary Source: Motor Control Module.
Action: Replace Motor Control Module.

May 07, 2012 | Fisher and Paykel Aquasmart wl80t65c

1 Answer

Fault 40 comes up


40. (00101000) Bowl Dis-engage Fault
While carrying out a bowl check, the Motor Control Module has found that the bowl is not
engaged even though the pressure sensor indicates that the bowl is empty. The Motor
Control Module continues to check for 2 minutes, after which time it displays this fault. The
first two areas to check are the clutch and the pressure tube. If these two appear correct,
then the fault could be in the pressure sensor in the Motor Control Module.
Primary Source: Mechanical.
Action: 1) Check that there are no clothes or other foreign objects preventing
the clutch from re-engaging. Excessive suds can stop the bowl
rotating.
2) If the machine is empty of water, carry out a clutch disassembly
procedure and check the spline drive.
3) Next check that the pressure tube has not come off and that it is
not kinked.
Secondary Source: Motor Control Module.
Action: Replace Motor Control Module.

May 07, 2012 | Fisher and Paykel Aquasmart wl80t65c

1 Answer

My front load washer won't spin fast anymore, any solutions out there?


A leading cause of clothing coming out very wet(not spinning on high speed) is over sudding (too much detergent being used) to see if that is the case start the washer without clothes and see if there is build up of suds (there should be NONE) to clean over sudding run a cold water wash and add a cup of white vinagar that will clean the build up of suds

Jul 18, 2011 | Washing Machines

1 Answer

Warning I have too many suds


Hi just read your posting.Now just a couple of questions.1st where is the machine draining the water to?Is it into the laundry sink or to another place?Have you removed the clothes from the machine?Have you tried putting a bucket or two of water manually into the bowl and put it to a spin cycle to drain the water out? Please reply with additional information and I can help you further.

Jul 06, 2010 | Fisher and Paykel Fisher Paykel Intuitive...

2 Answers

GE Front Loading Washing Machine seems to be holding water....


The high speed spin of a front load washer should normally do a good job of getting squeezing out the water but if there is an oversudsing condition that makes it hard for the drain pump to operate then the suds and water will just stay there. First make sure there is no actual clog in the drain line then run a load with no soap or detergent and see what happens. It's always better to use a low suds detergent with this type of machine

Mar 08, 2008 | GE WSXH208A Front Load Washer

Not finding what you are looking for?
Fisher and Paykel GWL11 Top Load Washer Logo

363 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...