Question about DISH Network IR Remote Control

2 Answers

Echostar IR remote (Dish)

The remote does not operate the devices. It has new batteries and when you press a button the buttons DO light up (so the remote works) it just appears that the signal does not reach the t.v. or dish box.

Posted by on

  • 1 more comment 
  • Anonymous Aug 16, 2008

    RCA TV Combo remote code

  • Anonymous Apr 21, 2009

    My IR remote doesn't work with the receiver.  I could set it up to work with my TV so I know the battery is fine.  I got a brand new remote from dish network and set it up.  Didn't work.  I got another receiver from dish network and it still doesn't work. My receiver is on my TV stand and I have a clear view on it.  TV2's (UHF) remote works flawlessly so only the IR is having problem. I am lost.

  • Anonymous Mar 26, 2014

    PVR BOOTS UP BUT NO SIGNAL FROM DSTV DISH

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 51 Answers

To set remote to tv
1)hold down tv button next to sat button in top left corner
2) when all buttons illuminate press 500 into remote
3)press pound sign
4)Hello, please help..
5)hold town tv button again.
6)when all buttons illuminate press big red power button
7)press up arrow once a second until tv shuts off
8)press # pound sign
9)try to turn tv back on w/ big red power button
10)if tv doesnt turn back on try again from step 2 but use down arrow instead

to set remote to receiver you need to access system info, if there is no sys info button on your receiver turn power off and press the up arrow, then press record 2 times on the remote,

Posted on Aug 06, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I GOT A NEW DISH REMOTE BUT WHEN I PUSH VOLUME BUTTON IT, CHANGES THE CHANNEL

Posted on May 01, 2009

  • elhsgrad1968
    elhsgrad1968 Dec 31, 2012

    what happens when you push the channel button? does the volume go up then?

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

TV CODE SONY


jose_luis_es,

I have listed the steps below to address the remote to your TV! I have also included the top 5 codes that work in case they are needed.

Codes: 500, 837, 627, 090, 185

1.) Press and hold the clear TV button until all mode lights light up.
2.) Release and TV light will be blinking.
3.) Enter the code and press #. The TV button should flash 3 times.
4.) Try functions (Volume, Power, etc..) and see if it is working.
5.) If no function, repeat steps 1-4 with another code.

Let me know if you need additional assistance!

Tommy Faust
DISH Social Media Representative

Dec 27, 2012 | DISH Network IR Remote Control

1 Answer

How do i make it so my echostar technologies dish tv remote uses the volume button


Allow me to help you with that, brandonmanvi! To get that programmed, go through the following steps, which will make both the TV and receiver respond to any remote control command:

  1. With the desired equipment on, press and hold the correct Mode button until all mode button backlights illuminate, then release.
  2. Press and release the Power button. AUX Mode: Before pressing and releasing the Power button
    • Press 0 for a TV
    • Press 1 for a VCR/DVD
    • Press 2 for any other device
    Then Press STAR (*)
  3. Press the Up button once a second while pointing the remote at the desired equipment. Note: If the code for the equipment comes up, the equipment will power off.
  4. Press the POUND (#) button. Note: If the code entered is valid for the remote, the mode light flashes three times.

Hope that helps!

Sep 10, 2011 | DISH Network IR Remote Control

1 Answer

I have an 20.0 IR EchoStar Technologies L.L.C 155681. For some reason the input button is not working. Whenever I press the TV button and press input it doesn't work. Does anyone know what the problem is?


Our remotes may not carry all of the normal functions your factory remote would. The remote you have is capable of learning additional functions, the link below will open a tutorial guide for this: www.dishnetwork.com/SupportSection/FileStream.ashx?ID=678

Daniel Busa
DISH Network
Customer Service

Apr 01, 2011 | DISH Network IR Remote Control

2 Answers

Need code to operate TCL tv with Dish remote


I have the 32" TCL and the 645 code also worked with the 722 dish network dvr remote (remote 20.0 IR). For that remote, press and hold tv button until all device buttons light up, enter 645 and press # key.

Jan 15, 2011 | DISH Network IR Remote Control

1 Answer

Dish Network IR Remote's SAT Mode Not Working ________________________________________ I programmed my Dish Network Remote (IR 1.5 Blue Button Remote Control ) for my Sharp 27F543 and now the remote would...


Hello, this is Nick Franta with DISH.

If you are trying to get the remote programmed to the receiver you can remove the smartcard from the receiver and that will prompt the system info screen. This will allow you to program the remote to the receiver.

If you need the process for programming the remote, here it is:
  1. Go to System Info screen (in this case -- obtain by removing smartcard from receiver)
  2. Hold down the SAT button until all mode lights light up.
  3. Enter a number between 1 and 15 using the numeric keypad on the remote.
  4. Press the pound (#) button
  5. Once the SAT button blinks three times, press record.
Hope this helps!

Jan 01, 2011 | DISH Network IR Remote Control

1 Answer

I have a dish network echostar remote control (20.0 IR). When I press any button that normally controls the satellite box, nothing happens except the green "sat" button on the top left lights...


Unplug the satelite box and replug it back like about an hour later.By letting the box resetting and upgrading it softwares the remote should work again now.

Dec 25, 2010 | DISH Network IR Remote Control

1 Answer

Replaced a Dish VIP722 with the new VIP722k,--got new remotes, also have a Bellvu 3100 on same primary TV. Used to be able to use one remote to control either recever boxes. How to I add the 3100 to the...


d1032d_junk3

If you are using the remote to operate an IR frequency, you can program that component to the VCR or AUX button on the new remote. I have provided the instructions on how to program the remote. I hope this helps.


Address To 2nd IR Receiver Using AUX Mode
  • Remote: 3.4, 4.4, 5.3, 5.4, 6.3, 6.4, 20.0, and 21.0
    1. Go to 2nd IR receiver
    2. Go to System Info Screen
    3. Hold down the AUX button until all mode lights light up.
    4. Press 3 then enter a number between 1 and 15 using the numeric keypad on the remote.
    5. Press the pound (#) button
    6. Once the AUX button blinks three times, press record. Note: If successful the number selected in step 4 will appear in the System Info screen under Remote Address.

Ray Calo
DISH Network

Jun 13, 2010 | DISH Network IR Remote Control

1 Answer

Sat button won't illuminate nor operate


Hi jscot myname is Mike Houston of DISH Network and I was going over your post and thereare a couple of things we can check. The first is to replace the batteries andafter the batteries are replaced push and release the SAT button and press select.If the SAT button did not light up the remote would need to be replaced.

Dec 30, 2009 | DISH Network IR Remote Control

1 Answer

3.1 DishnetWork remote problem


I suspect that the remote address got changed somehow. Pree and hold the sat button on the top left hand side of the remote until all buttons light up across the top and release. Now key in 0-1 on the numeric keypad and press the pound sign. The SAT button will flash three times. After it the SAT button is done flashing press the small red dot record button. Now try to operate the remote. You should be able to control the system now. Thanks for using Fix Ya.

Mar 13, 2009 | DISH Network IR Remote Control

2 Answers

I need the code for an echostar remote ir103602


How to Program a EchoStar Remote Control
Instructions

Step1
Ensure that the remote control has new batteries installed. If you are not sure or have been using the device for a while, go ahead and insert fresh batteries. You need four AAA batteries.
Step2
Locate the mode buttons on the controller. You will see SAT, AUX, TV, and VCR. SAT stands for the satellite receiver. Your remote is automatically set up to work with your EchoStar receiver, and you do not need to program it for this function. AUX may refer to a cable television device or an audio device that hooks it into your stereo system. TV refers to your television set. VCR may be chosen to control a standard VCR or a DVD player.
Step3
Press the mode button that corresponds with the device which you want to control with the EchoStar remote control. For example, if you want to program the remote to control the TV, press down the TV mode button.
Step4
Turn on the device. This is the item you want to control with the EchoStar remote. You may need to do so manually or with its own remote control. In this example, you would turn on your television set with its own control.
Step5
Press down the EchoStar mode button for the device again, but this time hold it down for three seconds. You are going to notice that all the other mode buttons are going to flash on. Aim the remote at the device you want to control.
Step6
Depress the EchoStar remote power button briefly and then slowly click either the up or the down arrow button. You are performing a code scan that allows the remote control to run through all the preprogrammed codes that are stored in its memory. Proceed slowly and do not hurry this process. It may take a few minutes, but it is virtually foolproof.
Step7
Stop when the appliance you want to control with the EchoStar remote control suddenly turns off. You have hit upon the correct code, and if you save it now, your remote will be able to use it in the future to control the functions of the item.
Step8
Store the code in the EchoStar remote control’s memory by pressing the pound button. You will notice that the corresponding mode button is going to flash, acknowledging the programming choice. You are now ready to control the item with the EchoStar remote control.

Aug 28, 2008 | Remote Controls

Not finding what you are looking for?
DISH Network IR Remote Control Logo

2,425 people viewed this question

Ask a Question

Usually answered in minutes!

Top DISH Network Remote Controls Experts

john milligan

Level 3 Expert

512 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Cindy Wells

Level 3 Expert

4758 Answers

Are you a DISH Network Remote Control Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...