Question about Washing Machines

1 Answer

Whirlpool AWM 8900 wont fill with water. Solenoid is ok but there is no power output to it from the control box. I fitted another control box from a known good machine but it still didn't fill. Eventually the machine displays "F" then "H" flashing. Note also that occasionally when the power is fist turned onto the machine the "no water" indicator is lit. Regards, Graham

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Perhaps the small rubber tube that comes from the drum to the pressure switch is blocked with soapy gunge ...what i do is PULL OUT PLUG to CUT OFF POWER .dis connect tube off pressure sensor and use ballon pump to clear tube. reconnect
tube to sensor and test machine.

Posted on Apr 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why does my washing machine not take in water? Can it be due the demo mode being set?


Have you connected the hoses correctly. If this ok and your washer is an electonic pc control you may have a faulty valve or solenoid as they are called.

Feb 10, 2015 | Whirlpool Washing Machines

1 Answer

Whirlpool awm 5100


Check voltage to motor at the time of the start cycle if water has filled, absence of voltage shows that the program controller is faulty, If there is power, then the motor is faulty, if the motor is humming or getting heated then there is friction on the drive, remove and clean the drive shaft.

May 02, 2013 | Washing Machines

1 Answer

Whirlpool awm 6100


It will be one of 2 things, a faulty inlet solenoid or an electronic controller issue, If you have a multimeter you can test the voltage supplied to the inlet solenoid and if there is voltage being supplied the valve is faulty, if there is no voltage then it is the electronics.

Mar 06, 2012 | Whirlpool Washing Machines

2 Answers

Whirpoll AWM 6000 does not take water.


What to check next is the water inlet valve. To do it, turn on the machine and start the filling cycle. If you cannot hear a faint buzzing or humming noise from the water inlet valve, the solenoid coil is not getting any power. Check it's wiring. If you can hear some noise, you need to replace it. Make sure to unplug the unit before doing any service.

Oct 18, 2009 | Whirlpool Washing Machines

1 Answer

My whirlpool awm 5125 wont fill up at start of washing


if it has just been installed check that the water tap has been turned on and the hoses have not been bent or twisted if these are ok you may have to replace the solinde valve in you machine

Sep 22, 2009 | Whirlpool AWM5125/1 Front Load Washer

1 Answer

The washing machine AWM 5104 does not fill with water, but the spin function is working ok. I have checked the hoses and cleaned the small wire filter.


madam not only cleaning the filter you should check the electric solenoid valve which will be fixed next to the filter. you can check it by giving power supply directly to the valve terminals,if it is working it will allows the water to flow-in or it wont then you should change it.

Aug 07, 2009 | Washing Machines

2 Answers

Whirlpool awm 8125/3 fault code FH


Probably too late, but here it goes:
FH means some cicle is taking too long time.
Replace the inlet electrical valve. It probably wont open enough and the water flow is not enough to fill to level in time. This should cost you 10€ and is easily done by anyone.
Just remove the top of the machine (two bolts on the rear and slide to the back), disconnect the valve (electrical and water input and output), push the lockers and twist the valve free.

Feb 07, 2009 | Whirlpool AWM8123 Front Load Washer

1 Answer

Washing cycle starts and takes hours even for short cycle.


Try checking for good water supply.
Pull out detergent tray and check for good water supply during filling.
if poor filling-
Try checking the hoses.
Turn taps off, disconnect from machine, place hose end in sink, turn tap on and check for good water flow.
if the hose has a red indicator in the side of the hose (end which is fitted to the tap) - Red indicator is a failed hose.(for models with Water Stop hose type "B")

Oct 05, 2008 | Whirlpool AWM6120 Front Load Washer

1 Answer

Whirlpool washer awm 6163


ckd for drain hose to low ..top needs to be 30-38 ins from floor also needs to be loose fitting in drain pipe to prevent siphoning ..if neither is the case ckd fill hoses for obstruction in screens last ch flow meter ..remove top round object left side with small hose from fill valve 1 side other side to detergent dispenser may try tapping it while it fills if works ok replace flowmeter

Sep 09, 2008 | Whirlpool Washing Machines

1 Answer

Whirlpool AWM 6100 wont let in water?


this may sound silly but is the hot and cold hoses around the right way

Feb 18, 2008 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

390 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...