Question about D-Link AirPremier DWL-2700AP 802.11g/b Wireless Access Point

1 Answer

Dwl-2700ap problems I get connected but speed is very slow

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 144 Answers

Hello!

-- try to change channel and enable security on your wireless network

-- remove other wireless devices on the network because that may cause wireless intermittent in your network

Posted on May 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 3 Dlink access points DWL3200AP for which I need D/C adapters. (connectors) power surges have ruined the conenctors event hough the access points are working well. Ihave been to the DLINK webpage...


You can use adapter of DWL-2700Ap and use POE to power your access point. It will work fine. If that is not available, you can mail us. we can arrange the adapter in India. You can contact us at cctplgoa@eth.net. Good Luck Anirban

Mar 09, 2010 | D-Link AirPremier DWL-3200AP 802.11g/b...

1 Answer

Sometimes i try to ping the wireless access point and i get the message 'Request time out',i receive this message even if im directly connected to the access point.what should i do


When you connect the computer directly to the access point, you might not be getting IP address on your computer.
You will need to assign a static IP address on your computer in the range of default IP address of the Access point.
Click Here for More info on access point

Oct 08, 2009 | D-Link AirPremier DWL-2700AP 802.11g/b...

2 Answers

DWL-2700AP reset default settings


Remove 13 screws from the perimeter of the back side of the DWL-2700AP and pull the covers apart. On the inside along the bottom adjacent from where the network cable plugs in, you will find a reset button. It is next to the white plug that leads to the antenna. You will need a flat screwdriver or something thin and sturdy to wedge between the casing and the reset button. While the AP has power, press the button and hold it in for a few seconds then release. Give it a few minutes and the factory defaults should be restored. Default IP: 192.168.0.50, Default subnet mask: 255.255.255.0

Jul 18, 2009 | D-Link AirPremier DWL-2700AP 802.11g/b...

1 Answer

Reset DWL 2700AP to factory defaults


Hi dear try to flow this tips it will help you
Administrator Settings
Administrator settings allow you to customize User Name and Passwords as an Administrator of DWL-2700AP. The default value of the Username is "admin" with no password entered.
Password
Enter a password in the Access Point Password field. Type the password again in the next field to confirm it. The Password is case-sensitive ("A" is a different character than "a",) and must be between 0 and 12 characters in length

System Settings
You may reset the DWL-2700AP back to factory settings by clicking on Restore Default settings.
Restore Default Settings
Choose Yes and click Apply to restore all Access Point settings to the factory default settings.

Thank you
Imran
Pls rank as possible

Apr 20, 2009 | D-Link AirPremier DWL-2700AP 802.11g/b...

1 Answer

DWL 2700 AP wrong firmware install


hi...
since you upgraded a different firmware try updating the firmware again with the correct firmware if it works fine if it doesnot then the router had gone bad,,
and for GeminiBS reset the router to the factory default since the firmware was not done in a proper manner may be it had interruptions..once the hard reset is done the computer is restored back to the default so that you can use the device..

vedhick

Feb 13, 2009 | D-Link AirPremier DWL-2700AP 802.11g/b...

1 Answer

DWL 2700 AP power light flashing, no IP


Yeah, not a good idea to have opened it if there is a warranty still in effect. Belkin, DLink, and Linksys are all made by the same corporation, Cisco, and generally a flashing power light indicates a fault condition. You may be better off getting a new one.

Dec 19, 2008 | D-Link AirPremier DWL-2700AP 802.11g/b...

6 Answers

How to probe the configuration or reset the 2700AP?


Restore it to default, with these things, if it wont work on automatic, then something is worng.

Feb 27, 2008 | D-Link AirPremier DWL-2700AP 802.11g/b...

Not finding what you are looking for?
D-Link AirPremier DWL-2700AP 802.11g/b Wireless Access Point Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Wireless Access Points Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

scramblepad
scramblepad

Level 2 Expert

66 Answers

Anthony Chiang
Anthony Chiang

Level 3 Expert

524 Answers

Are you a D-Link Wireless Access Point Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...