Question about Frigidaire Affinity ATF7000E Front Load Washer

1 Answer

Cloths were soaked !Won't restart, door locks and you hear a buzzind sound ??

Cloths were soaked like it didn't finish its cycle, no codes where shown! Tried to restart washer & door locks and all you hear is buzzing sound !!
I don't have a owners manual so I don't know how to diagnose the system!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 216 Answers

Greetings JohnnyWrench,

Information provided by the manufacturer would indicate a few things possibly causing this:

1) Washer was overloaded, remove some of the clothes and continue the cycle.

2) Washer load was too small. Add 1 or 2 similiar items to help balance the load.

3) Load is out of balance, rearrange clothes to allow for more balanced spin.

4) Drain hose might be kinked, straighten drain hose.


You can also find a copy of your owners manual at
http://www.frigidaire.com/products/laundry/washers/front_load/prod_ATF7000FS.asp

I hope some of this helps!

Thank you,

Dorothy
Go Ahead. Use Us.

Posted on Apr 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Frigidaire washer won't finish cycle


Hello Ellen Greer - This particular issue can be caused by quite a few reasons. Washer could be experiencing a communication error from the main control board, faulty door lock assembly, faulty pump or the timer itself is not operating correctly. Did you notice a humming noise? If so, either the drainage hose/pump is clogged and needs to be cleaned or could possibly have another issue with the door lock assembly or pressure switch. You can also press and hold the start/pause and cancel button together at the same time for approximately 30 seconds to display an error code on the LED. What error code does it display? However, I would suggest contacting a professional to accurately diagnose the washer.

Nov 14, 2012 | Frigidaire ATF6000ES Front Load Washer

1 Answer

I pushed the 'pause' button during the wash cycle of my LG WD-3274HD and now the door won't open.


Hi!

The machine knows it dint't finish the washing cycle, and, because it may be possible that water is still a lot inside, the door is locked.
If you are shure the door can be opened without the water coming out by the door, simply disconnect it from the electrical supply and wait a few minutes until the door unlocks. (you will hear the unlock click)

Good luck!

Aug 08, 2011 | LG WD-3274RHD Front Load Washer / Dryer

1 Answer

My machine is showing the code FL machine has problems locking. How do I resolve this problem


Your Maytag Neptune Washing Machine displays error codes, also called "help codes," to identify specific problems with your washer. Once you close your Maytag Neptune's door, the machine locks the door, goes through the selected wash cycles and unlocks the door when the laundry is finished. Error codes appear when there are problems with the door, the inflow and drainage of water and the motor.
The "FL" code indicates that the washing machine was unable to lock the door after you closed it. Open and close the door tightly, then restart the washing cycle.
Door lock monitor switch in door lock mechanism unable to communicate to control board the door is locked.
1.Check wire connections in harness leading from machine control board to door lock mechanism.2.Check solenoid and door lock enable switch in door lock mechanism.
3.Replace responsible component.

Dec 07, 2010 | Maytag Neptune FAV6800AW Top Load Washer

2 Answers

If you get the FL how do you get the door to open??


  1. Your Maytag Neptune washing machine displays error codes, also called "help codes," to identify specific problems with your washer. Once you close your Maytag Neptune's door, the machine locks the door, goes through the selected wash cycles and unlocks the door when the laundry is finished. Error codes appear when there are problems with the door, the inflow and drainage of water and the motor.
  2. Do
  3. Your Maytag Neptune washer displays the "do" help code when the washing machine is trying to start a cycle, but the door is open or not locked properly. If this message is displayed, close the door securely and restart the washing cycle.
  4. FL
  5. The "FL" code indicates that the washing machine was unable to lock the door after you closed it. Open and close the door tightly, then restart the washing cycle.
  6. Sd
  7. The "Sd" code indicates that you have added too much detergent to the washing machine and your laundry has too many suds. The machine will stop displaying this code if it has successfully run the suds recovery cycle, which removes the excess suds from the wash load. If the code remains, reduce the amount of detergent in the load. Use less detergent for similar loads of laundry in the future.
  8. PF
  9. The "PF" code indicates that a power failure has occurred. Restart the wash cycle. If the code still appears, check that the washing machine is still plugged in to the electrical outlet.
  10. Nd
  11. The "nd" code indicates that your Maytag Neptune is not draining as it should. Check that the drain hose isn't kinked and that the stand pipe isn't clogged. If you find either of these problems, fix them before restarting the washing cycle.
  12. LO
  13. The "LO" code appears when the washing machine has finished the selected wash cycle, but cannot unlock the door. Verify that the door is closed properly, push the "Off" button, and wait two minutes. The door should unlock and the error code will disappear. If the error code remains, unplug the washing machine, wait two minutes and plug it back into the electrical outlet.
  14. Lr
  15. The "Lr" code indicates that the washing machine's motor is not running as it should. Have your Maytag Neptune washing machine serviced by a certified Maytag repair professional.

Dec 06, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Door not locking nor spin cycle not working


Hi.

Before proceeding to spin the timer does a check on the lid switch.

You should be able to fix the problem replacing the lid switch.

Regards.

Ginko.

Jul 26, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Spin cycle


it sounds like there is either an obstruction in the pump, or the load is getting off balance during the spin cycle. two things to try, fill the washer with no cloths in it, when it starts to agitate, stop the cycle and put it in drain/spin cycle. the water should be out in under a minute. its hard to see because the door locks, but you can hear a difference in the pump when its out, or after 60 seconds, press cancel and open the lid to check. if the waters out in that time, the pumps ok. then run it through the spin diagnostic with a load of cloths. make sure the cloths are wet, and a normal load you wash. this will check to see if the load is getting off balance, and shutting down during the spin cycle. let me know if you still have the problem. good luck, shane

Aug 23, 2009 | Maytag Neptune Washer

1 Answer

Maytag washer


check to make sure the door is locking when it should. If the door isn't locking or sensing that its locked the washer will not go into high speed spin.

Mar 31, 2009 | Maytag Neptune MLG2000A Front Load Stacked...

1 Answer

Washer won't start cycle after door is closed


Try taking the top of the machine off and checking all of the electrical connections, including the one to the door lock. I have to do this about once a month with my machine and it seems to work.

Jan 20, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My wash will not spin fast enough to get all the water out


A model # would be helpful, but sounds like you have a clogged pump. Send me the model and Ill let u know for sure. Dave www.washermd.com

Dec 12, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

Wet cloths need help please!!!!!!!


F9=Overflow Condition
If the Overflow contact on the pressure switch is Closed for more than 60 seconds and Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service.



Check the drain hose and make sure it is not plugged or inked.

Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU)

Check/Clean Drain Pump Filter of foreign objects

Check for Drain Pump Failure

Check the Inlet Valve for proper shut off

Check the Pressure switch for proper operation

Nov 08, 2008 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Frigidaire Affinity ATF7000E Front Load Washer Logo

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...