Question about Projection Televisions

1 Answer

Need setup instructions and codea - Projection Televisions

Posted by on

  • donmooris Apr 30, 2008

    need codes and instructions for ONE FOR ALL Big Easy remote control!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

You can find the remote control codes for difrent brands of devices from
http://www.hifi-remote.com/ofa/codes-tv.shtml

If none of the codes work then we have two other solutions:

1. Searching For Your Code

If you have tried all of the set-up codes for your brand of equipment ,or your brand is not listed, and you are still not able to get the unit to respond, try the following procedure to search for your code.
If you don't find a code that works, the remote will flash four times when you reach the end of all the codes for this device type.

  1. PRESS the button for the device you want to program, (TV, VCR, CABLE, etc.), then RELEASE.
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. ENTER 9-9-1 (two blinks on the remote)
  4. ALTERNATE slowly between the POWER key and the DEVICE (TV, VCR, CABLE, etc.) button until your device turns off. (On VCR, LD, and CD players use PLAY instead of POWER)
    Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
  5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.
2. Learn the buttons from the original

Line up your original remote and the head-to-head before completing the following steps.
  1. PRESS and HOLD the SETUP button until the red LED flashes twice.
  2. PRESS 9 - 7 - 5, the red LED will flash twice.
  3. PRESS the DEVICE key where you wish to learn the function. The next 3 steps must be completed within 10 seconds.
  4. PRESS the button that will receive the learned function, the LED will flash radidly.
  5. PRESS the button on the original remote to be learned.

Now you can repeat steps 3 through 5 to learn other functions onto other keys or press and hold SETUP until the Cinema's red light flashes twice to lock in your new feature. (If the red light does not blink twice, stop and repeat steps through 6).
To test the new feature, press and release the device key in which the new feature was learned followed by the key on which the feature was learned

More help for programing your remote can be found here: http://www.hifi-remote.com/manuals/ofa-l.shtml?URC-7800#device

If you find that the solution/answer I provided led you to, or resulted in a fix, please take a moment to close the ticket with a FixYa! rating. I would be very grateful for your show of appreciation.

Thank you for using FIXYA!

Cheers!
IrishDruid

Posted on Apr 30, 2008

  • Swilin Sampson
    Swilin Sampson May 03, 2008

    Hi,




    Just wanted to inquire if your issue is resolved, or if there is anything
    further I can do to assist you…





    If you find that the solution/answer I provided led you
    to, or resulted in a fix, please take a moment to close the ticket with a FixYa!
    rating under my solution.
    I would be very grateful for your show of appreciation.





    Should you have any further questions, please feel free to
    post them here.





    Thank you for using FIXYA!





    Cheers!


    IrishDruid

  • Swilin Sampson
    Swilin Sampson May 31, 2008

    Hi,




    Just wanted to inquire if your issue is resolved, or if there is anything
    further I can do to assist you…





    P.S. -You can rate this solution with one of
    four votes, if you feel your issue is resolved.






    • "FixYa!"
      - The solution provides great advice on how to solve the problem.
      (Positive Rating)

    • "Helpful"
      - The solution provides useful leads that helps solve the problem.
      (Positive Rating)

    • "Thanks
      for Trying
      " - The solution does not solve the problem but the
      effort is appreciated. (Negative Rating)

    • "Inappropriate"
      - The solution has absolutely nothing to do with the problem.
      (Negative
      Rating)


    If your issue is not still not resolved, do not
    assign a rating just yet. Please post back as to what steps you took, results,
    etc, and I will try to assist you further as best I can.






    Thank you for using FIXYA!





    IrishDruid




×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust the convergance? I have a shadowing problem


Press menu on the remote then scroll down to setup then enter setup. The auto convergence feature is listed there which will reset it automatically. If auto convergence disappeared from the setup menu then you will need the RCA convergence option missing repair kit from www.tvrepairworld.com which does contain the instructions.

Jun 10, 2011 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

I need to know what convergence board I need and part number. TV is RCA Model HD52W59YX36. Symptom is see 3 d like shadows. When I go to do the covergence adjustment from the setup menu....nothing appears...


You dont need a convergence board. The convergence option missing from the setup menu is a easy cheap repair. www.tvrepairworld.com has the kit called ITC222 & 222A convergence option missing repair kit. It also has the CD with instructions along with the three components that repair that problem.

Mar 27, 2010 | RCA HD52W59 HDTV Projection Television

1 Answer

Need help with Harmony One remote and Mits WD-65736


To ensure the remote controls your devices properly, you must disable Net Command.To disable Net Command you must delete all devices associated with it.

Open the Mitsubishi Television's setup menu.
Select Delete at the setup menu.
Select Entire Configuration and then select Next.
Follow the onscreen instructions to delete the entire configuration.
To finalize your selections and complete the NetCommand setup, select Finish from the finish screen.
#messageContent0_1 {font:10pt Tahoma,Verdana,sans-serif;}

Feb 01, 2010 | Mitsubishi WD-65736 Television

1 Answer

I have a PT-47WX53 that has one vertical bar down the middle of the screen. Barely visible in a purple hue and about 3-4 inches wide. I'm looking for some suggestions. Thanks


A few simple things you may try. Under your menu on the tv look for convergence or it also may be under setup. Run the convergence setup and follow the on screen instructions. If the tv fails to converge while in setup you may need to replace some things however the parts are very very cheap. If your convergence setup works and you still have a bad picture, and or both, meaning the tv's convergence wont align then you may need 1 or 2 IC's and maybe need to change your coolant in the tv's RGB lens...all can be done with little experience and for under 50 bucks. I can give more detail if needed.

Dec 28, 2009 | Panasonic PT-47WX53 47" Rear Projection...

1 Answer

I need a diagram of how to set up the analog converter box or instructions.


Hi,
I am posting the instructions of how to set up the analog converter box :-
Hope it will you.
· Things you’ll need:
Analog TV, antenna, two coaxial cable, and converter box

· Instructions:
Step 1
Unplug coaxial cable on the back of TV "antenna in" (RF) port
Step 2
Insert coaxial wire into the "antenna in" on the converter box
Step 3
Use second coaxial wire and plug in the converter box, "out to TV" port. Plug the other end into
“antenna in" on the TV
Step 4
Power on the converter box and TV. Change TV channel to 3 or 4. Follow on screen instruction to
Complete setup.
Step 5
After setup you will begin to see more channels than before with better clarity. Some stations will broadcast two or three channels. Enjoy

Please let us know if that was helpful enough.
Good Luck & Thanks,
Shiv.

Aug 18, 2009 | Projection Televisions

1 Answer

THE TV IS CONNECTED TO CABLE BUT THE PICTURE COME OUT STATIC WHAT IS THE PROBLEM


Check your setup instructions for your TV. f you're actually using a cable TV service, your setup would be different than for on-the-air TV. Normally - using your remote - press MENU then SETUP and select Cable TV. I'm assuming your TV isn't an older model TV.

Aug 18, 2009 | JVC AV-48P775 48" HDTV

1 Answer

Need set up instructions and codes for toshiba tv -remote


If this Hand unit is not a universal Remote there is No set up codes for it,It must be Factory unit you have ,you can buy remote unit with codes at Dollar store for 5.00

Jan 06, 2009 | Mitsubishi VS-50605 50" Rear Projection...

5 Answers

Setup DVD&VR375


Check this link
http://in.youtube.com/watch?v=C-i26YB6ttE

Sep 01, 2008 | Samsung Projection Televisions

2 Answers

I need a code # to program my Universal RCA remote for my Prima TV and my DVD player


I own a One-for-All universal remote, and my booklet says the setup code for a Prima TV ( without a built-in DVD or VCR) is one of the following numbers: 0761, 0783, 0815, 0817. I can not guarantee these numbers will work with your remote, but it is worth a try.
I assume your DVD has been attached separately, and not built into the TV. In some cases, you might not need an additional setup code. Once the TV has been turned on, you simply push the DVD button on your remote, to activate the DVD. The instructions which came with your remote and your DVD should provide you with more details. If the instructions indicate that an additional DVD setup code is required, then please respond by telling me the brand name of your DVD.

Jul 04, 2008 | Projection Televisions

2 Answers

What is the setup code for a Sylvania TV with Model Number RLC372AK01 and Serial Number 25014897? I need it to program a new remote control I recently purchased. None of the codes listed for Sylvania TVs...


The setup code may be different for each brand of remote, so a code for the TV will not help. You need to follow the instructions for the remote you bought to scan through all codes until you find one that works. Generally this is done by entering the programming mode and using the ch-up or ch-down buttons to scroll through the codes then use the power putton to see if it turns your set off. When you find the right one you press the button to 'store' it.
Your remote instruction booklet should step you through the process. If it does not have instructions for scanning all codes let us know the Brand and Model of the Remote you bought and we may be able to find the instructions.

Apr 16, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...