Question about Vacuums

1 Answer

I want to download a manual for fantom cyclone xt

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Legend:

    An expert who has written 200 answers of more than 400 characters.

  • Expert
  • 310 Answers

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=558003
Generic problem for all Vacuums
I want to download a
Posted by dotbeeman on Apr 29, 2008
I want to download a manual for Fantom Cyclone XT


Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
The best way is to go the Fantom website that I will include @ the bottom of this response and to see if the website will allow you to download the owner’s manual, or you can call the Fantom Factory / Manufacturer and they will most of the time send you out an owner’s manual to the cust or @ least make copies and mail them to you. You also can check with your local vac dealer. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.
http://www.fantom.com/fantom/default.aspx
Customer Service – 1-800-798-7395
For technical support, please call us toll-free at 1-800-798-7398. Hours are Monday through Saturday from 9:00 am to 6:00 pm Eastern Standard Time.
Thanks, Don – The Vac Man
Go Ahead. Use Us.

Posted on May 09, 2008

2 Suggested Answers

RJones1125
  • 373 Answers

SOURCE: How do i replace the belt in the Fantom Cyclone XT vacuum

remove the covers over the headlights and under the shiny foul. there are two screws. there are two tabs that hold down the cover over the wheels, they just pop on/off with a click.
on my xt. i had to remove the rolling brush and clean out all the hair that was stuck in the bearings. remove the screw holding down the motor and belt. pry out the roller brush to get to the bearings. there was some serious hair ball in there.
reassembled mine and it works perfectly now :)

Posted on Feb 18, 2009

  • 17 Answers

SOURCE: Fantom Cyclone XT Vacuum Cleaner

Here is the owners manual which goes over some troubleshooting problems.

http://www.fantom.com/fantom/manuals/Cyclone.pdf

At first I would think it was the thermal overload, which is covered in the manual. But I would guess that you have let it sit for 30 minutes to cool down and tried again and the vacuum still didn't work.
I would think you may have one of four problems.
1. Your thermal overload was tripped and is stuck and will need replaced.
2. You have a clog in your vacuum lines or the brush roller is froze, which keeps causing the thermal overload to trip.
3. Your power cord has a short, which would need replaced.
4. Your power switch is bad, which would need replaced.
Out of these 4 possible problems I would say the only one you could fix on your own would be problem #2. Make sure the vacuum is unplugged and take the brush roller off and clean it, make sure it moves free. Check your vacuum lines to make sure you do not have a clog, other wise the motor does not get air flow to cool it down causing the thermal overload to trip. As for problem 1, 3, and 4 I would suggest taking it to a repair shop.
Hope this helps, post back.

Posted on Jul 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Fantom F11063 Cyclone Vaccum


I think the manual can help you in replugging the wires

How did you pull out the wires from circuit board ?
Is it with professional help or through some other means



Sep 18, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

1 Answer

How do i replace the belt in the Fantom Cyclone XT vacuum


remove the covers over the headlights and under the shiny foul. there are two screws. there are two tabs that hold down the cover over the wheels, they just pop on/off with a click.
on my xt. i had to remove the rolling brush and clean out all the hair that was stuck in the bearings. remove the screw holding down the motor and belt. pry out the roller brush to get to the bearings. there was some serious hair ball in there.
reassembled mine and it works perfectly now :)

Dec 19, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

1 Answer

Parts


Hi,

TheFantom Cyclone XT was originally manufactured by Fantom Technologies,Inc. that closed in October 2001. The replacement for a Fantom CycloneXT would be Westinghouse Wired Deluxe Edition (either a WST1550 or a WST1551). These replacement products are now handled by Salton Inc. Perhaps you may inquire from them:
  • Salton Inc.
  • 1 800 616 8689
  • salton@saltonusa.com
Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Aug 20, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

2 Answers

Fantom Cyclone XT Vacuum Cleaner


Here is the owners manual which goes over some troubleshooting problems.

http://www.fantom.com/fantom/manuals/Cyclone.pdf

At first I would think it was the thermal overload, which is covered in the manual. But I would guess that you have let it sit for 30 minutes to cool down and tried again and the vacuum still didn't work.
I would think you may have one of four problems.
1. Your thermal overload was tripped and is stuck and will need replaced.
2. You have a clog in your vacuum lines or the brush roller is froze, which keeps causing the thermal overload to trip.
3. Your power cord has a short, which would need replaced.
4. Your power switch is bad, which would need replaced.
Out of these 4 possible problems I would say the only one you could fix on your own would be problem #2. Make sure the vacuum is unplugged and take the brush roller off and clean it, make sure it moves free. Check your vacuum lines to make sure you do not have a clog, other wise the motor does not get air flow to cool it down causing the thermal overload to trip. As for problem 1, 3, and 4 I would suggest taking it to a repair shop.
Hope this helps, post back.

Jul 11, 2008 | Fantom Vacums XT450K Upright Vacuum

1 Answer

Fantom Cyclone wiring


Hi,

The only sure way recommended (and probably the safest) would beto get a service manual or at least a schematic diagram. The FantomCyclone XT was originally manufactured by Fantom Technologies, Inc.that closed in October 2001. The replacement for a Fantom Cyclone XTwould be Westinghouse Wired Deluxe Edition (either a WST1550 or a WST1551). These replacement products are now handled by Salton Inc. Perhaps you may inquire from them:
  • Salton Inc.
  • 1 800 616 8689
  • salton@saltonusa.com
Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Jun 08, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

1 Answer

Fantom Cyclone XT


The top edge pieces will pop off, tabs hold them in place, then you take it apart.

May 27, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

2 Answers

Circuit board


You should be able to locate parts for your vacum at this link by entering the model number.
http://www.fantom.com/fantom/default.aspx

Mar 25, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

Not finding what you are looking for?
Vacuums Logo

Related Topics:

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Roger Potts

Level 3 Expert

694 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...