Question about Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

1 Answer

No cleaner or water will squirt out when I am shampooing. Yes, I have plenty of water, cleaner, power and set on floor cleaning bissell proheater 2X

Posted by on

  • 5 more comments 
  • Anonymous Jan 27, 2009

    bissell 9500 pro heat x2 will not spray water

  • Anonymous Jan 28, 2009

    no water will come out....grrrr

  • Anonymous Jan 31, 2009

    I have the same problem. . .I have taken the unit apart to see if it was a loose hose or clogg and had a hard time taken the hoses off. Has anyone done this?

  • kntckygrl23 Jan 31, 2009

    my cleaner will not work for the floor...the hand tool works tho

  • dinanagrace Feb 09, 2009

    Same problem!!! No water or soap solution will come out when trying to clean the floor. BUT it will work using the hand held .... RRRrr!!! Aggrevating!

  • Anonymous Feb 14, 2009

    No water or cleaner will cxome out but the hand held is working.

  • Anonymous Feb 16, 2009

    I have the same problem after using it 3 times. Very irritated

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Legend:

    An expert who has written 200 answers of more than 400 characters.

  • Expert
  • 310 Answers

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=618960&thid=556844
No cleaner or water will
Posted by sherski3 on Apr 29, 2008
No cleaner or water will squirt out when I am shampooing. Yes, I have plenty of water, cleaner, power and set on floor cleaning Bissell proheater 2X

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
Bissell 9500 ProHeat 2X Clean Shot Upright
This could be that you have a defective water valve assm below the water tank or the trigger assm is not working properly or not connected. You may want to refer to your owner’s manual and check out the trouble shooting guide for no water coming out. You may want to contact the factory or manufacturer to see if they have service tech support or to send out a new owners manual for your current model #. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.
http://www.bissell.com/ By Phone Customer Service:
(800) 237-7691 Hours:
M-F 8:00 a.m. - 10:00 p.m. ET
Saturday 9:00 a.m. - 8:00 p.m. ET

Don – The Vac Man
Go Ahead. Use Us.

Posted on Apr 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Wont spray water on the carpet


Same Problem here- The hand piece works fine. Bissell 9500 ProHeat2X.

Both tanks full New Belt on the brushes I can not get cleaner/water to spary when trying to clean the floors.

I've taken my air-compressor and with low psi blown back to make sure teh lines are clear from the spary heads. Still not working...


Apr 17, 2010 | Bissell 9500 ProHeat 2X CleanShot Upright...

1 Answer

Just got a bissell proheat clearview force cleaner, we press the trigger, no water sucking action or shampoo release going on .. what's wrong?


By the Floor Cleaning setting knob and Tools for PreHeat setting knob, there's a red x inside a clear circle cap. Is it spinning at all? If not...twist the cap off and remove the red x. Under the red x there is a tiny little filter. This might be plugged. Pull it out and clean it. Put back in (this is all really easy).
See if it works now.

Dec 24, 2009 | Bissell 1699 ProHeat Clear View Upright...

1 Answer

The water and shampoowon't come out but it cames


This model is famous for burning up the silinoid switch that allows the water to come out the bottom to clean the floors. That will need to be replaced, but my recommendations is to take this model back and bet your money back. It is engineered bad!

Nov 25, 2009 | Bissell Carpet Cleaner Powerbrush Deep...

1 Answer

A solution to many "non-spray" problems.


The Scotchguard is going to be dicey inside the Bissell, yes, as you have learned the hard way.

I think the Bissell and the Hoover shampoos sold for their carpet cleaning machines are reasonably safe to use in the Bissell. My own personal favorite for use with the Bissell is the Hoover Premium Pet Formula, which is pricey but effective even if you don't own pets. I also pre-treat stained areas with Resolve Carpet Cleaner, a few minutes before using the Bissell.

I don't know what will happen with your home brew containing Dove. It may work well.

Jun 06, 2009 | Bissell 9500 ProHeat 2X CleanShot Upright...

2 Answers

Cleaner Solution Not Dispensing On Bissell 9200 Pro Heat Cleaner


I haven't had this particular issue (yet... knock on wood!) with my Bissell, but remember that the shampoo will not dispense with no water in the tank (the most common cause of this issue because sometimes you think it has water but it doesn't) or water not flowing through the machine due to clogged sprayers-- another issue-- but since you're getting water on the floor that is not your issue-- or with the handle locked in position. If none of that fixes it, try removing the shampoo container, stand over a sink, and push your finger up inside the grommet where the shampoo container mates with the Bissell. Shampoo should dribble out. If it doesn't, unscrew the grommet (holding the container upside down of course so the shampoo doesn't gush out) and use your finger and running water to try and the grommet cleaned out.

If this isn't helping, it may be that your soap pump or soap dispensing trigger switch are defective.

Oct 20, 2008 | Bissell 9200 Upright Vacuum

1 Answer

Bissell PROheat 2X shampoo carpet cleaner


http://geeksquad.fixya.com/ThreadView.aspx?prdid=618960&thid=565019
Bissell ProHeat 2X shampoo carpet cleaner
Posted by boomerboo on May 02, 2008
I don't have the instruction for this machine; if you could help me with were to put the water and cleaning solution and how much. Thank you, Sharon my email address is sharonlee326@yahoo.com
Comment by boomerboo, posted on May 02, 2008
I need direction on how to use the shampoo carpet cleaner

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. Bissell 9500 ProHeat 2X Clean Shot Upright. The best place to get the owner’s manual for the Bissell is to check the Bissell website or to call the Bissell factory or manufacturer and give them the Model # of your unit and they will mail you out one. Always use genuine Bissell products made for the model that you have for best results. So check with your local factory authorized vac dealer that carries and services Bissell. I will give you the Bissell factory phone # listed below for further questions. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://www.bissell.com/ Customer Service 1-800-237-7691
Hours of Operation Monday thru Friday 8:00 am to 10:00 pm EST
Saturday 9:00 am to 8:00 pm EST
Mail To: Headquarters, Bissell Homecare Inc
P.O. Box 3606 Grand Rapids. MI 49501
Thanks, Don the Vac Man
Go Ahead. Use Us.

May 02, 2008 | Bissell 9500 ProHeat 2X CleanShot Upright...

1 Answer

How to use bissell carpet cleaner


On the 1698 modle thier is a large clean water tank and a smaller shampoo bottle which seats on the side of the machine.
the shampoo goes in the smaller bottle fo the two.

Jan 02, 2008 | Bissell 1698 PowerSteamer ProHeat Upright...

1 Answer

Bissell 1699n proheat clear view problems


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be on the tank, not in the hole. The flow indictor cap is leaking air or maybe is too tight. If you had the top cover off, make sure that the tubes are routed right so as not to get pinched when the cover is put back on, the smart mix knob should be in the water setting and that the piston is on the bottom of the smart mix know. Pump is bad.

Sep 22, 2007 | Bissell 7901-1 ProHeat Scotchgard Upright...

Not finding what you are looking for?
Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum Logo

332 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bissell Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Roger Potts

Level 3 Expert

694 Answers

Brad Brown

Level 3 Expert

13561 Answers

Are you a Bissell Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...