Question about Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

1 Answer

Frigidaire Gallery Professional Series

Once the washer has 50 left on the timer and goes into the HO mode...a clicking sound starts and the display light starts to flicker. If I stop the machine and let it sit for a few moments it will proceed...for a while...then the same intermittent clicking and light flashing will begin.

Posted by on

  • tscri Aug 12, 2008

    Same problem...blinking and clicking during the HO cycle on a 900 series Frigidaire Gallery dishwasher.

  • tscri Aug 20, 2008

    We paid $90 for a service call to be told that the whole control panel needed to be replaced. Cost of the panel is $180 and installation is $70. We will run it until it dies and then buy a Whirlpool.



×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 409 Answers

I would check the warranty on the control board, if that is what the tech recommended. most mfg. cover electronics longer than the appliance itself.

it could also just be the keypad.

Posted on Sep 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I get my Frigidaire Dishwasher 900 series to start?


Sounds like you have a bad door switch. You might also have a motor that tends to freeze or lock up. It could possibly be a bad motor capacitor too. Does this help?

Mar 18, 2015 | Frigidaire Gallery Dishwashers

1 Answer

Frigidaire gallery stove


Hello mnwpictures - Based on the symptoms you are describing the range may either have a faulty EOC (electronic oven control) or a potential wiring failure. Try resetting the range by unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes and then turn the unit back on. Does the control panel have a display? If the issue persists, I would recommend contacting a professional to proceed further. Most likely the EOC on the range will need replacing.

May 12, 2013 | Frigidaire Professional Series 24 in....

1 Answer

My dishwasher by Frigidaire Gallery Professional Series Model gpd8998jc0 has all lights flashing and could not be started. I smelled burning from dishwasher. Could it be motor burning?


Hello,

it could be the motor depending on where it's coming. You can remove the lower panel, there are only two screws that hold it on. Look under their and inspect the motor.

Another part that could cause this issue is the mother board. The board is located behind the control panel. Remove the screws around the door frame to loosen and remove the control panel.

On most of these you also have to remove the plastic shielding that cover the control board. To do so remove the three or four screws that mount the board down.

Often these control boards will burn and create a smell like this.

Let me know.

Mar 26, 2011 | Frigidaire Professional Series 24 in....

2 Answers

My frigidaire dishwasher model #fghd2433kf1


It is in a delay wash mode.
Disconnect power for 60 seconds.
Re-connect power.
Press the Cancel button.
Press the regular wash cycle and start the dw.

Jul 17, 2010 | Frigidaire Dishwashers

1 Answer

Dishwasher is on and running a load. It is flashing HO??


The "HO" means it's trying to heat the water to the appropriate temperature before proceeding in the cycle. It's totallly normal, and can go on for 20 minutes or so... if you run your sink faucet to clear the line of hot water first, it will reduce the time it takes to heat the water

Apr 03, 2010 | Frigidaire Professional Series 24 in....

1 Answer

Frigidaire gallery prof series dishwasher- arms dont work


Call a certified repair company as it sounds like the sump is clogged for some reason.

Jan 29, 2010 | Dishwashers

3 Answers

"HO" flashes on display during washing.


HO, indicates that the dishwasher is using Hot Water. It is completely normal.

Mar 08, 2009 | Frigidaire Professional Series 24 in....

1 Answer

I want to know what HO means on a frigidaire dishwasher?


it means the water is trying to heat up and it is taking longer than normal. Check your hot water heater to make sure it is heating properly. Do not use hot water in other areas at same time ..ie: washer, shower, etc. The HO will disappear once the water is heated to the proper level by the dishwasher.

Dec 31, 2008 | Frigidaire Dishwashers

1 Answer

Error code HO on frigidaire gallery series dishwasher


If your hot water isn’t hot enough it will display “HO” while heating the water to operating temperature

Sep 06, 2008 | Frigidaire Dishwashers

Not finding what you are looking for?
Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher Logo

1,086 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Dishwashers Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Carmen Mikulic

Level 2 Expert

409 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Frigidaire Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...