Question about Kodak i40 Path-Through Scanner

1 Answer

Acrobat 8.1 When i test my kodak i40 scanner thru the scan validation tool, it works great, but when i try to scan anything, at any settings (typically simplex 150 dpi grayscale 8.5 x 11 size, i get one of two messages: scanning failed or file cannot be found. I've used the scanners native interface and the adobe interface, same results. current 8.1.2 is latest version of acrobat: any suggestions: Roxyll

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Upgrade to Acobat 9.0 Pro. It seems to work in that can scan pages for a document, HOWEVER, adding/appending to already scaned pages for a document seems to crash 9.0. For example, say I scan in pages 1 - 4. I cannot then scan pages 5 -6 as part of the same document--crashes Acrobat.

I think this finally proves the problem is Acrobat 8.0 and NOT the i40 drivers.

Posted on Mar 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes a kodak i700 scanner to keep running?


Could be the setting in the driver (scan validation tool) time out or if the feeder roller continues to turn clean the sensor located on the paper tray inside the square hole approx 8 mm X8 mm just below where the feed rollers are located

Jun 19, 2014 | Kodak i780 Sheetfed Scanner

1 Answer

Kodak i40 scanner error 8 message but lamps are fine, worked OK last week, any suggestions


Check you have the latest firmware , the old version can cause this on startup especially when cold

Oct 10, 2011 | Kodak i40 Path-Through Scanner

1 Answer

My scanner is cutting of some of the page. what should I do? My printer is a dell printer.


depending on the type of software you are using, this could be where the problem lies. test the scanner using the scan validation tool.
Start>All programmes>Kodak>Document Imaging>Scan Validation Tool - use the TWAIN driver.

If the scanner scans fine here, then this is software related and you will need to contact the software manufacturer to resolve the issue.

Nov 13, 2009 | Kodak i1220 Pass-Through Scanner

2 Answers

Error 8 in scanner i40


Error 8 = Face up light check failure.
Check Top Lamp is lighting up and not Flickering.
Check connections to Ballast (Inverter) and Lamp.

Jun 30, 2009 | Kodak i40 Path-Through Scanner

1 Answer

Check kds.log -this is my massage error when i press scan option at canner kodak i 260 "check KDS log" messge error appears when scan option chosen on i40 Kodak Scanner.


Try Calibration routine. If it fails check optics are clean and not scratched. If it still fails change the lamps.The KDS.log is encrypted and can only be accessed via a license key. This is only Available to Kodak reps or through RTS ltd service calls.
WWW.Responsets.co.uk.

Mar 25, 2009 | Kodak i40 Path-Through Scanner

1 Answer

Kodak i40 Scanner - paper jamming


First clean with a damp cloth, then try Isopropyl Alcohol. Dont use solvents. Check if papers are sticky. Stapled papers are 'sticky' even after removing staples. loosen them if required. Notmally rollers last 200,000 to 250,000 scans
S. Mohan, Chennai, India

Mar 17, 2009 | Kodak i40 Path-Through Scanner

1 Answer

Kodak i40 Front loading scan


Hi,

Try downloading the latest Firmware for the Kodak i40 Scanner at the following Kodak.com page: http://graphics.kodak.com/docimaging/US/en/Products/Document_Scanners/Desktop/i40_Scanner/Support/Drivers_And_Downloads/i30_and_i40_Scanner_Firmware/index.htm

Follow the instructions carefully, and make sure that the scanner and the PC DO NOT turn off while doing the Firmware update. I recomend connecting both to a UPS with a known good battery while doing this upgrade.

This should install the latest features including the one that enables front feed.

Otaron

Jun 02, 2008 | Kodak i40 Path-Through Scanner

1 Answer

Selected scanner was not found adobe acrobat


first downloaded the trial version of Acrobat 7.0 and removed
Acrobat 6.0. Test scanning ok it will worked!

Proceed to uninstall the Acrobat 7 trial version and
reinstall the 6.0 version you own, try this i hope it will work for you.

All d best

Mar 29, 2008 | Kodak Open Box i50 Flatbed Scanner

2 Answers

Error 5


I can't seem to find a error code 5. What software are you using to scan? Did the error start right after your first? Had the scanner been working?

Jul 12, 2007 | Kodak i40 Path-Through Scanner

Not finding what you are looking for?
Kodak i40 Path-Through Scanner Logo

Related Topics:

341 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Scanners Experts

Andrew Taylor
Andrew Taylor

Level 3 Expert

10708 Answers

John Bowen

Level 2 Expert

331 Answers

ray gallant

Level 3 Expert

36340 Answers

Are you a Kodak Scanner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...