Question about Rinnai Heating & Cooling

Open Question

Convert model 60df natural gas to lpg. - Rinnai Heating & Cooling

Posted by on

  • albert1937 Apr 29, 2008

    Yes need to convert rinnia 60DF heater to LPG.Can't buy kit.I live in the lismore area.Many Thanks. John Drewitt.

×

3 Suggested Answers

  • 736 Answers

SOURCE: I have bought a natural

at the end of the pipe that loosely goes into the burner assembly, there is a nut or metal part that has a small hole that the gas goes through ... that is the "gas jet" .. they have different size holes for natural and lp gas .. the manufacturer should have both .. usually it just unscrews and the new one screws in its place .. there would be one for each burner .. if there is only one burner then you need just one replacement jet with a hole size suitable for Lp gas .. you might be able to get the new jet from a local hardware store if you take the old one with you so they can get the size and style right ..

Posted on Oct 09, 2010

jdhnmi
  • 143 Answers

SOURCE: I have wall mounted Vulcan

there is a difuser where the gas comes out and there is a different part for each type of gas. the gas regulator should stay the same you will need a new difuser. dont know if i spelled it right but that is what it is

Posted on Mar 26, 2011

Testimonial: "thank you very much...."

  • 5 Answers

SOURCE: I have a Bonaire RT21/NG

Most of the time, all there is to do is remove the regulator spring and replace with a kit for the specific model of valve you have cause there are a lot of them out there regardless of who made it. So yes it can be done easy and for peanuts but one has to know is way around gas to do the job safely. A picture of the gas train and the valve would help a lot. Remember, 1 manufacturer can use many types of valve depending on where it is sold due to local rules & regulations. Hope this helps Regards from Canada Guy

Posted on Aug 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Coleman furnace 4322/729 model lights the pilot but won't cut in . What could be problem ? Cleared lines Complete


Gas valve not opening? Does it have the exhaust blower that pulls vacuum switch allowing burner to light?
(1) Thermostat not working? Has to complete the circuit in or gas valve to open.
(2)Can be a stuck or bad gas valve. Try tapping the side of the gas valve body while thermostat is calling for heat. Tapping,not pounding. Like lightly,yannow? don-ohio (:^)

Jan 03, 2017 | Coleman Heating & Cooling

1 Answer

Cannot get gas to flow to pilot flame with main valve parallel to gas pipe. Is there something I must push to make gas flow to the pilot flame pipe?


you said, in effect: Cannot get gas to light the pilot flame even though manual supply valve is open. Is there something I must push to light [ignite] the pilot? Permalink
The gas supply valve is open, and the pilot gas cutoff valve is open but [it seems like] gas will not flow to the pilot flame because it will not light when I supply a match or lighter flame. I remember there is a button or something I need to press...but where it it? I cannot find it.

Nov 03, 2014 | Heating & Cooling

1 Answer

Igniter or gas valve problem


It could be a connector or wiring defect.

Jan 19, 2014 | Heating & Cooling

1 Answer

Heat will not blow hot air model #310aavo48090oabjd serial #0205a42429


give name make of unit and set up of system oil/gas ect...

Oct 28, 2012 | Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rinnai Heating & Cooling Experts

paulcarew

Level 3 Expert

2046 Answers

blender719

Level 1 Expert

53 Answers

Kenneth Wilson
Kenneth Wilson

Level 1 Expert

45 Answers

Are you a Rinnai Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...