Question about Samsung HC-P4752W 47" Rear Projection HDTV-Ready Television

2 Answers

Cant find parts

Hi i have same problem but i have six bunt resistors aswell i cant find replacement ones anywere dose any one no were to get them they are,

Posted by on

2 Answers

I tried several places as well and found them at, they were the only place that shipped, i had them 3 days later. I just did this 2 weeks ago.

Posted on May 01, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Samsung Master
  • 8,617 Answers

The resistors are 3.9OHM you can get the ICs you need as well as the risistors at the following link. They also provide free instalation instructions and free online instant messageing with a tech when you do the actual repair. If your model is the HC-P4752 you will need two STK392-010 Convergence ICs as well. heres the link.

Posted on Apr 29, 2008

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The blue color is arching along with the yellow and i cant converge them enough someone told me about having the color CHIPS or what ever they are called replaced. I would need to know whta the part...

You can get the PT53WX53 convergence repair kit from which is the correct one for your model. The Kit contains the Convergence ICs the six resistors and the Cd with instructions.

Jan 14, 2010 | Panasonic PT-47WX53 47" Rear Projection...

1 Answer

Dead Mitsubishi WT42313

hello when you changed the stk are there any resistors near by if so these need to be tested aswell also any capacitor near by these need to be tested desolder 1 end so you get a good reading on the meter i think the resistor are 39 ohms good luck


Nov 05, 2009 | Projection Televisions

1 Answer

Kp46wt500 covergence problem

Check the fuses. If a convergence amp goes out, usually one or both fuses go as well.
I'd check the power resistors in the vicinity for opens as well.

Sep 13, 2009 | Sony KP-46WT500 46" Rear Projection...

2 Answers

Convergence parts? What are the specific pico fuses and resistors

There are six 3.15 amp picos use 3.5 amp when replacing and there are two 5 amp picos on the G board the resistors if needed are 4.7 ohm 1/2watt

Sep 06, 2009 | Sony KP-46WT510 46" Rear Projection HDTV

1 Answer

The red will not line up. What part do I need to replace?

Replace both STK392-110 Ics and check the six 2.2 ohm 2watt resistors. Heres a link to the repair kit for your model which contains both ICs and all six resistors plus step by step instructions with pictures on how to do the repair.

May 06, 2009 | Panasonic PT-47WX53 47" Rear Projection...

1 Answer

Convergence problem

did you replace the six convergence resistors with the ICs? as Hitachi recommends replacing the six resistors when the ICs are replaced as the old ICs can harm the resistors and they will need replacement.

Sep 27, 2008 | Hitachi 53FDX20B 53" Rear Projection...

1 Answer

Failed resistor

those are the convergence feed resistors. # blinks on a panasonic means convergence IC failure. You will need to replace the two stk392-110 convergence ICs and the six resistors. You can get replacement ICs and resistors at the following link.

Sep 06, 2008 | Panasonic PT-53TW53 53" Rear Projection...

1 Answer

42H83 Convergence

Yes the convergence ICs need to be replaced, however so dont the six 1.8 ohm 1watt resistors as Toshiba recomends replacing those six resistors when the ICs are changed. You can get the 50H71 / 50H82 Convergence repair kit as the 42H83 is identical to the 50H71 series, so the kit will work for your model. Heres the link where you can get the kit.

Aug 10, 2008 | Toshiba 42H83 42" Rear Projection...

1 Answer

Blue convergence

Thats the classisc sign that you need to replace both convergence ICs. You will need two Convergence ICs STK392-120 and then six resistors they are RK42 3.3 ohm 1watt, RK46 1.5 ohm 1watt, RK50 2.7 ohm 1watt, RK54 1.5 ohm 1watt, RK58 3.9 ohm 1watt, RK62 1.8 ohm 1watt. You can get replacement ICs and resistors at the following link and they provide free instalation instructions with pictures so you can repair the set yourself. Heres the link.

Jul 10, 2008 | Hitachi FDX Series 43FDX10B 43" Rear...

1 Answer

The magic focus is off on my do i fix it and if i need parts were could i get them from?

You will need to replace bothe STK392-110 Convergence ICs and the six resistors . You will need two 3.3 ohm 1 watt metal film resistors for RK42 and RK50, then two 1.8 ohm 1 watt metal films for RK46 & RK54, then one 3.9 ohm 1watt metal film for RK58 and finally one 2.2 ohm 1watt metal film for RK62. You can get the two replacemnet ICs and the resistors at the following link and they will include fre instalation instructions with pictures so you can do the repair your self.
Here is the link.

Jul 05, 2008 | Hitachi Projection Televisions

Not finding what you are looking for?
Samsung HC-P4752W 47" Rear Projection HDTV-Ready Television Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

Donald Griswold
Donald Griswold

Level 1 Expert

8 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Are you a Samsung Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides