Question about Dyson Memory CRO1 Front Load Washer

3 Answers

I have error code f13, can you help, please..

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 1 Answer

This s is how i fixed the F-13 Fault on my Hotpoint WD 640 washer dyer. Simple to fix just see the pictures and explanation. Hope this clears things up
Boxie


i have error code f13, - 1_7_2013_12_28_59_am.jpg1_7_2013_12_31_38_am.jpgi have error code f13, - 1_7_2013_12_31_56_am.jpg.net/uploads/images/1_7_2013_12_31_56_am.jpg" alt="1_7_2013_12_31_56_am.jpg" class="h_mi" />

Posted on Jan 07, 2013

  • Martin Box Jan 07, 2013

    Sorry pictures are to low a resolution and are unclear, sorry. Cant seem to change them!!! Send me an email and i will post them to you :)

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 27 Answers

F13 means not heating

the element may be faulty or the wiring to it
flooding gives fault f14

Posted on Aug 08, 2010

  • makathjem Dec 06, 2010

    F13 is the heating element. It is at the bottom of the drum at the front. If you know how to remove the front panel then it is reasonably easy to change. You can also test the continuity before you change it. I got a new element for under 20GBP. The element is held in place by the bolt on the earth point. It takes a bit of working to get it out as the rubber seal is deformed as it is installed in order to make a tight seal. I ended up removing the front of the drum as well. About 3hrs DIY work start to finish so perhaps worth the call out fee.

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,416 Answers

Hello,

what f13 indicate means an error code that there have been an over flow of water from the drum over to the panel or the wire that suppl power to the screen .

what you will have to do to fix up this problem from the screen is to unscrew the screws with screw driver care then trace the wire ,that is the power supply down to the panel and also to the screen clean up all forms of liquid around the wires and also the panel carefully . then couple it back with care to is position with this the problem is solve.

thank you.

Posted on Aug 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F13 and F11 codes pop up


F13 is
Dispenser Circuit Error
If the dispenser motor is not able to be driven to it's proper position.
Check mechanical linkage from dispenser motor to the top of the dispenser
Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU)
Check Dispenser Motor

i snagged this answer from another site
i think its a worn bit of plastic
as it becomes britten when not always wet
much like a boat out of water

Mar 05, 2015 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

1 Answer

Frigidaire fault code f13 kitchen range what does that mean ?


Thank you for your inquiry, raymond bouley!

I understand that your Frigidaire range is displaying an error code of "F13". An "F13" error code typically stands for a bad EEPROM (Erasable Programmable Memory) identification or check sum error. The best way to clear this code is to disconnect power from your range for roughly ten minutes. If you continue to experience an issue it could be a possible that you have a faulty board or wiring harness. I would then recommend having a professional out to perform a diagnosis on your range. Hope this helps. -Matt

Jan 13, 2015 | Frigidaire Kitchen Ranges

1 Answer

F13 code


Hello friend, thank you for your post!

Based off the information you have provided your question is under an "F13" error code but you also stated that it is showing you an "F1" error. I have researched both error codes for you. "F13" usually indicates error identification, which could be an issue within your control board. "F1" typically can indicate that the range has detected an issue with the runaway temperature (overheating). Both codes could be corrected with a reset, which you can do by flipping the household circuit breaker for roughly ten minutes. If that does not correct the issue I would recommend contacting a professional. I hope this is helpful. -Matt

Aug 07, 2014 | Frigidaire Ovens

1 Answer

How to fix f13 error code on a tappan stove


Good Afternoon Friend,

I understand that you are receiving an F13 error code on your Tappan range. I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your washer status has changed successfully. If further troubleshooting is needed, I ask that you please leave your model number in the comments as well. Hope this is helpful.

-Best Regards-
WP

May 31, 2014 | Frigidaire FEF336BC Electric Kitchen Range

1 Answer

F13 error code on Ariston washer dryer combo


Model ARMF 125 with same error code F13 how to fix please advise Thks

Nov 06, 2011 | Hotpoint-Ariston ARWDF129NA Washer

1 Answer

I have a Frigidaire Elements stove. When I went to preheat the oven I got a constant 'beep' and a code, F13 ERR. Please help Thank-you Anxious in Indy


Hi akadiki,

This error code F13 description is a bad Clock ERC. The steps below will help you determine whether the ERC or touchpad is defective.

Warning: If you feel in any way uncomfortable performing this test or making this repair, please contact a qualified appliance repair technician.

1. Disconnect power to the range (unplug the range power cord or turn the power off to the range at the circuit breaker). It is very important that the power to the range has been disconnected, so please double check before continuing.

2. Gain access inside the control panel.

3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC.

4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was.

5. Turn the power back on.

6. Wait for at least one hour to see if the F13 code comes back (usually accompanied by a beeping sound).

7. If F13 comes back, replace the ERC. If it does not, replace the touch pad.

Hope it helps.

Thank you for using FixYa.

Sep 15, 2011 | Kitchen Ranges

2 Answers

What does F13 Error mean?


Hello,

Here is what the F-13 error code means and the fix for it.

F13 Internal CPU checksum errors 1. Disconnect power for 1 minute.
2. Reconnect power.
3. If failure remains, replace the touch control module

So it says the main computer control had detected a error in the touchpad control

I hope this helps,

Gene

Aug 01, 2011 | Kitchen Ranges

2 Answers

It appears F13 error


hi sir we have ARISTON washer and DRYER model : AQXXMD129EX its a error coming F13 please help me soon

Dec 21, 2010 | Ariston Technologies AWD120 13 lb. Washer...

1 Answer

I get a error f13 when i turn on broiler


http://www.appliancepartspros.com/repairtips/repairtips_appliance+fault+codes.aspx
Above are the codes and meanings.
The "F13" error code means "Bad EEPROM identification/Checksum error".

If reseting the power does not help then according to Frigidaire suggested corrective action the electronic oven control (aka EOC) has to be replaced.

- The part number for the EOC is AP3874704


Dec 13, 2010 | Frigidaire Kitchen Ranges

1 Answer

My kenmore elite electric slide in range displayed error and F13 and the oven won't turn on


i phoned Sears about error code f13 on a gas range, and was told to unplug the range for 30 minutes. i think she meant 30 seconds - to reprogram the microchip. i unplugged it for 15 minutes or so, then reconnected, and it worked.

Jul 09, 2008 | Kitchen Ranges

Not finding what you are looking for?
Dyson Memory CRO1 Front Load Washer Logo

887 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dyson Washing Machines Experts

Brad Brown

Level 3 Expert

15729 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1466 Answers

paul
paul

Level 3 Expert

822 Answers

Are you a Dyson Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...