Question about Kenwood Audio Players & Recorders

Open Question

Kenwood sw-300/powered subwoofer how is it that you connect the wires? from the reciever,subwoofer n the other speakers....

Posted by on

5 Suggested Answers

  • 3422 Answers

SOURCE: I have a Kenwood KR-V7030

HI,
The protect message means that a problem was detected and that the output speaker connections have been disabled.

Posted on Jun 29, 2008

lynchms
  • 93 Answers

SOURCE: Powered Or Unpowered Subwoofers For Onkyo TX-8511

Greg- Powered subs are better than non-powered subs (also known as passive subs), anyway I see the TX-8511 has no sub pre-out on the back panel, so you need to decide what sub you will use and run from the receivers left and right speakers output into a subwoofers speaker in from speakers then back out to speakers, look at the back of a subwoofer and you will see like 4 sets of speaker hookups 2 in and 2 out, what this does is takes the low end or bass and drops the signal to the subwoofer then takes the mids and highs out to your left and right speakers, unless your regular left and right stereo speakers have large woofers a sub is the way to go.

Posted on Jan 28, 2009

  • 14 Answers

SOURCE: Can't connect subwoofer to onkyo av receiver

you would need a y jack to connect those to the receiver

Posted on Mar 05, 2009

  • 1 Answer

SOURCE: Sub-woofer output not working

"Sub-woofer output not working" problem, and notify you when a new solution is offered.
Press the setup key on the front of the receiver
Select the subw setting
Move the multicontrol knob until the sub woofer is on
Turn off the receiver and turn back on- the subwoofer should be on

The operator manual can be downloaded on the web site--- free

http://www.retrevo.com/support/Kenwood-VR-507-Receivers-manual/id/480ag219/t/2/

Posted on Mar 21, 2009

Shaul Dag
  • 30 Answers

SOURCE: Connecting a subwoofer to a KR-V6080

As long as you change out the connectors, you can run it anywhere you wish. I suggest a rear channel.

Posted on Jun 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenwood vr606 reciever shutting off subwoofer and centre speaker simultaneously after few minutes/seconds of powering on. WHat's the cause?


The receiver's out put sections are grouped in pairs. Front left and right in one output, rear left and right in second output, and center channel and sub output on the third. Sounds like a semiconductor or semiconductors have gone bad in the center & sub output.

Nov 19, 2015 | Kenwood VR-606 Receiver

1 Answer

I have a Kenwood sw 22HT subwoofer. It will work only when I hit it from the back. Can anyone help me find out what the problem is? Thanks!


Sounds to me like a loose connection on a wire. Take it apart and just give it a good looking over. Mainly check the speaker wires and the power supply connection.

If you have a multi tester that would be helpful, but in your
case it sounds like a simple fix.

Feb 04, 2015 | Kenwood Audio Players & Recorders

1 Answer

I want to connect kenwood woofer sw-07 to pioneer amplifier vsx-d859tx. i am unable to connect please guide me.


Hello,

I don't recall correctly if your Pioneer has a sub out RCA connector, and if the Kenwood SW-07 has a low level input. So the usual way is to connect it using the speaker wires.
You connect either the FL or the FR to the sub and it should work.

Good luck

Jan 11, 2015 | Pioneer Audio Players & Recorders

1 Answer

Can I hookup a powered subwoofer to a Kenwood 105VR receiver?


Had you bought the 106 version that has a subwoofer out socket. Some subwoofers have options for connection by speaker terminals. If you haven't bought the subwoofer yet check with the seller to make certain you can connect it via speaker wires. Otherwise you would be better with a non powered one.

Aug 03, 2013 | Kenwood 105VR

1 Answer

Connecting a passive subwoofer to a denon 2113


you need another reciever/amp to power that sub, because that denon reciever is designed for a powered sub,. if you have another old reciever/amp laying around, you can connect the sub out from the denon into an auxillary input of any old reciever/amp, (switched to that input) with speaker wires from old reciever/amp to the passive sub

Mar 05, 2013 | Denon Avr-2113ci 7.1-channel Home Theater...

1 Answer

How do i connect it to a the subwoffer sw 50 ht


on the back of your receiver is a subwoofer pre-out, connect one cable here, and connect the other end of this cable to your subwoofer - line level in. (depends on your subwoofer and receiver) but that's how mine is connected. yours will be similar.

Feb 10, 2010 | Kenwood VR-505 Receiver

1 Answer

Speaker wire for subwoofer


Usually, a subwoofer will have its own built-in power amplifier. Thus, it will be designed to plug into a standard RCA jack (the type used for DVD players, etc). rather than having wires to connect to a speaker terminal block. Look for a jack on the back of the receiver called "Subwoofer", or simply "SW". If your subwoofer has 2 single wires, it WON'T work with your reveiver's subwoofer output, as this output only carries a line-level signal and is not amplified. You would need a separate power amplifier for this type of SW. If your SW speaker has a DVD-type plug, it should work fine with the receiver's SW output jack.

Jan 02, 2009 | JVC RX-554V Receiver

1 Answer

I have a Kenwood Subwoofer, SW-305, S/N 00901468, that when the power is one and hooked up there is a loud buzzing sound. No audio comes out of the subwoofer. I have checked and rechecked my conections and...


please try to replace your RCA plug that connects from your input player to your Kenwood Subwoofer..coz it not have open ground or has no continuety in it

Dec 05, 2008 | Audio Players & Recorders

2 Answers

Subwoofer Connection: Speaker wire to Mono RCA


The easiest solution to use your subwoofer is to buy an amp for it. Any old stereo receiver from a garage sale will probably do just fine.
  1. Connect the mono RCA subwoofer output from your Sony with a 1xRCA-to-2xRCA splitter to both the left and right input of the cheap reciever's tape or aux input
  2. connect both speaker outputs of the cheap reciever to the speaker input on your subwoofer. make sure both black (-) outputs on the reciever connect to the black input on the sub, and the red outputs (+) on the reciever are both connected to the red input on the subwoofer.
  3. make sure the cheap receiver's volume is all the way down. turn your Sony up to about the loudest you'll listen to it. turn up the subwoofer amp until it's loud enough to sound good.
  4. leave the subwoofer amp alone, the Sony volume will all you ever need to touch from now on.

You can even now turn off your subwoofer / adjust the volume easily now!

Oct 30, 2007 | Audio Players & Recorders

1 Answer

Sub-woofer output not working


"Sub-woofer output not working" problem, and notify you when a new solution is offered.
Press the setup key on the front of the receiver
Select the subw setting
Move the multicontrol knob until the sub woofer is on
Turn off the receiver and turn back on- the subwoofer should be on

The operator manual can be downloaded on the web site--- free

http://www.retrevo.com/support/Kenwood-VR-507-Receivers-manual/id/480ag219/t/2/

Sep 22, 2007 | Kenwood VR-507 Receiver

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

787 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

sonic boom...
sonic boom...

Level 3 Expert

1557 Answers

Are you a Kenwood Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...