Question about Canon NP 6230 Copier

1 Answer

Canon 6230 =E 065 switch the power off and on again

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

The Power Suply Is Faulty and Cek The DC Control.

Posted on Aug 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set ink level on canon mx-320 after refill?


Apparently the problem is that you are choosing to install (according to Canon), cheap, aftermarket ink cartridges rather than Canon ones. Therefore the machine is not recognizing them. Try this procedure, found on another forum, that was supplied by one of the cheapo ink companies. Who better to know how to fool the machines than them. If they want to sell these ink carts, they better know who to make them work!

U051 Error Correction procedure.

1- Switch off the Canon MX300 and disconnect the power cable.

2- While press and hold the power button, Connect the power cable to electric socket.

3- While pressing the power button, press the "Cancel/Stop" button (red button). (press TWICE che "stop\cancel" button)

4- Now release the power button and the printer turns into a kind of factory mode. Wait for 10 seconds until it says "idle".

5- Press ">" (next button) once "Shipping Mode 3? then Press the "OK" button. Press "OK" again for "without cleaning". A test page will print.

6- Open the cover, like you are about to change the cartridges.

7- Disconnect the power cable again without switch off the printer.

8- Take out the both cartridges.

9- Close the cover.

10- Connect the power cable and turn on the printer.

11- Now just put the cartridges back and the ink level in the canon Pixma MX300 have full again.

Jan 14, 2015 | Canon Black Pixma Mx 320 High Quality...

Tip

How to Reset Ink Level Canon MX300 Cartridges


1. Switch off the Canon MX300 and disconnect the power cable.<br /> 2. While press and hold the power button, Connect the power cable to electric socket.<br /> 3. While pressing the power button, press the "Cancel/Stop" button (red button).<br /> 4. Now release the power button and the printer turns into a kind of factory mode. Wait for 10 seconds until it says "idle".<br /> 5. Press "&gt;" (next button) once "Shipping Mode 3&prime; then Press the "OK" button. Press "OK" again for "without cleaning".<br /> 6. A test page will print.<br /> 7. Open the cover, like you are about to change the cartridges.<br /> 8. Disconnect the power cable again without switch off the printer.<br /> 9. Take out the both cartridges.<br /> 10. Close the cover.<br /> 11. Connect the power cable and turn on the printer.<br /> 12. Now just put the cartridges back and the ink level in the canon Pixma MX300 have full again.

on Feb 17, 2011 | Canon MX300 Office All-In-One Printer

1 Answer

How to reset canon mp258


Reset Canon MP258 Printer procedure:
1. Press power button / power switch
2. Plug cable power with holding power button
3. Press Reset button one, release power button and press reset button twice until control panel show "O".
4. Press "+" buttom, display changing from 0 to 1
5. Press Power Button again , Printer will be print 1 page
6. Open printer cover
7. Unplug power
8. Take out cartridge 810 and 811
9. Plug power
10 . Press power switch
11. Open scan cover
12. Insert cartridge 810, 811

Aug 02, 2011 | Canon Office Equipment & Supplies

2 Answers

How do I re set the cartridges after a refill on my Canon PIXMA MX320?


Hi there

Here How to Disabling Low Ink Level Notification for Canon IP and MP, the method to reset
Ink level notification:

1. Push “resume” for 5 seconds for canon For MPXXX you must enter to service
Mode.
2. Push Power switch then remove power cord.
3. Insert plug power cord while pressing “power switch” at the same time.
4. Push Start/reset by step 2 continue Wait display shown “0′
5. Push + change display from “0′ to “1′
6. Push colour button 2 times
7. Push Power switch again, Printer will print 1 page
8. Open cover
9. Unplug power cord
10. Take out ink cartridge #40 and #41
11. Insert plug again
12. Push power switch
13. Open cover (scan cover)
14. Insert ink cartridge #40 and #41 again


Enter to service mode for canon MPXXX

With the printer powered off but connected to a power source, press the Power
Button while pressing and holding the Stop/ Reset button.
When the Power is lit, press the Stop/Reset button two times while pressing and
Holding the Power button.
When releasing the Power button and the Stop / Reset button (regardless of
Order), the printer will move into a service mode. (Waiting for menu selection)

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Apr 30, 2010 | Canon PIXMA MX310 All-In-One Printer

2 Answers

How to reset error e4


The reset method work for canon printers that using PG-40 and CL-41 cartridge. After doing this reset method canon printer will not display low ink notification anymore and will not show error code “E4′ or “E5′.
Here How to Disabling Low Ink Level Notification for Canon IP and MP, the method to reset ink level notification:
  1. Push “resume” for 5 seconds for canon IPXXXX. For canon MPXXX you must enter to service mode.
  2. Push Power switch then remove power cord.
  3. Insert plug power cord while pressing “power switch” at the same time.
  4. Push Start/reset by step 2 continue Wait display shown “0′
  5. Push + change display from “0′ to “1′
  6. Push color button 2 times
  7. Push Power switch again , Printer will print 1 page
  8. Open cover
  9. Unplug power cord
  10. Take out ink cartridge #40 and #41
  11. Insert plug again
  12. Push power switch
  13. Open cover (scan cover)
  14. Insert ink cartridge #40 and #41 again
Enter to service mode for canon MPXXX
  • With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
  • When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
  • When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)


Apr 15, 2010 | Canon PIXMA MP210 Photo All-In-One Printer

1 Answer

Resetter


http://safemanuals.com/annexe_MX310%20series%20Easy%20Setup%20Instructions_CANON_PIXMA%20MX310-_E.htm
The reset method work for canon printers that using PG-40 and CL-41 cartridge. After doing thisreset method canon printer will not display low ink notification anymore and will not show error code “E4′ or “E5′. This method takes from indoreset yahoo group and prepared by Choy.
Here How to Disabling Low Ink Level Notification for Canon IP and MP, the method to reset ink level notification:
  1. Push “resume” for 5 seconds for canon IPXXXX. For canon MPXXX you must enter to service mode.
  2. Push Power switch then remove power cord.
  3. Insert plug power cord while pressing “power switch” at the same time.
  4. Push Start/reset by step 2 continue Wait display shown “0′
  5. Push + change display from “0′ to “1′
  6. Push color button 2 times
  7. Push Power switch again , Printer will print 1 page
  8. Open cover
  9. Unplug power cord
  10. Take out ink cartridge #40 and #41
  11. Insert plug again
  12. Push power switch
  13. Open cover (scan cover)
  14. Insert ink cartridge #40 and #41 again
Enter to service mode for canon MPXXX
  • With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
  • When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
  • When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
http://downloadprinterresetter.blogspot.com/
OK, go to website above, and download a "Resetting" tool, this makes resetting easier to do.

Apr 09, 2010 | Canon PIXMA MX310 All-In-One Printer

1 Answer

My printer reset button keeps flashing. i have switched it on and off and still does not work 1p3500


Hi there

Here How to Disabling Low Ink Level Notification for Canon IP and MP, the method to reset
Ink level notification:

1. Push “resume” for 5 seconds for canon For MPXXX you must enter to service
Mode.
2. Push Power switch then remove power cord.
3. Insert plug power cord while pressing “power switch” at the same time.
4. Push Start/reset by step 2 continue Wait display shown “0′
5. Push + change display from “0′ to “1′
6. Push colour button 2 times
7. Push Power switch again, Printer will print 1 page
8. Open cover
9. Unplug power cord
10. Take out ink cartridge #40 and #41
11. Insert plug again
12. Push power switch
13. Open cover (scan cover)
14. Insert ink cartridge #40 and #41 again


Enter to service mode for canon MPXXX

With the printer powered off but connected to a power source, press the Power
Button while pressing and holding the Stop/ Reset button.
When the Power is lit, press the Stop/Reset button two times while pressing and
Holding the Power button.
When releasing the Power button and the Stop / Reset button (regardless of
Order), the printer will move into a service mode. (Waiting for menu selection)

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Feb 20, 2010 | Canon PIXMA iP3500 Printer

1 Answer

5100


Hello there ok

Try
Here the Solution to reset the ink level for Canon Pixma MX300 follow this steps to reset the ink level in your canon MX300.

1. Switch off the Canon MX300 and disconnect the power cable.
2. While press and hold the power button, Connect the power cable to electric socket.
3. While pressing the power button, press the “Cancel/Stop” button (red button).
4. Now release the power button and the printer turns into a kind of factory mode. Wait for 10 seconds until it says “idle”.
5. Press “>” (next button) once “Shipping Mode 3′ then Press the “OK” button. Press “OK” again for “without cleaning”.
6. A test page will print.
7. Open the cover, like you are about to change the cartridges.
8. Disconnect the power cable again without switch off the printer.
9. Take out the both cartridges.
10. Close the cover.
11. Connect the power cable and turn on the printer.
12. Now just put the cartridges back and the ink level in the canon Pixma MX300 have full again.
Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks


Feb 07, 2010 | Canon MX300 Office All-In-One Printer

1 Answer

Canon ip1800 printer not working


Hi,

when the yellow led flashes is never a good signal... you should check the manual's printer to find out the error code meaning "4 yellow flashes and 1 green)
Usally it's the waste tank that is full, in this case you need to:

  1. Push “resume” for 5 seconds for canon IPXXXX.
  2. Push Power switch then remove power cord.
  3. Insert plug power cord while pressing “power switch” at the same time.
  4. Push Start/reset by step 2 continue Wait display shown “0′
  5. Push + change display from “0′ to “1′
  6. Push color button 2 times
  7. Push Power switch again , Printer will print 1 page
  8. Open cover
  9. Unplug power cord
  10. Take out ink cartridge #40 and #41
  11. Insert plug again
  12. Push power switch
  13. Open cover (scan cover)
  14. Insert ink cartridge #40 and #41 again

Jul 18, 2009 | Canon PIXMA iP1800 InkJet Photo Printer

1 Answer

Canon 8400f will not power up


I know this sounds stupid, but did you make sure to switch the power switch to the ON position? When the power is connected, and then you flip the power switch on, the light inside the scanner will illuminate, possibly briefly but noticeable. If that doesn't happen, then you're not getting power. Try different outlets. Re-secure power cord connection. If still no power, then I suggest to contact Canon (techsupport) for another power cable.

Jul 11, 2008 | Canon CanoScan 8400F Film Scanner

Not finding what you are looking for?
Canon NP 6230 Copier Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

1986 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...