Question about Audio & Video Receivers

1 Answer

I have peavey 212 heritage guitar amp footswitch plug broke. I have new one but i need wire diagram please include colors and speaker conection.Thank U very much

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Call the Peavey Customer Service line (number available @ the Peavey site) and get the parts department to email you a schematics on the amp... it has the footswitch wiring on it. And it's free to do this.

Posted on Mar 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello,I'm trying to conect 4 speakers(Bose 161,4-8ohms,50w each) and 2 speakers (JBL cf100(3way speakers),8ohms,100w each) to rceiver Pioneer VSX-455, I want to conect all of them at the same time.please I...


Well if you look on the back it plainly says speakers should be between 8-16 ohms.

It has facilities for 2 pairs of fronts (A and B) which could be run concurrently if they met the >8-ohm spec.

http://www.use.com/PIONEER_767cb5bb4ea6f30a06fc?p=7#photo=9

http://www.use.com/showorig.pl?set=767cb5bb4ea6f30a06fc&p=6

The JBL's would work best as primary front speakers.

http://www.retrevo.com/support/JBL-CF100-Speakers-manual/id/597bh151/t/2/

If you wired the Bose in series with each other, they'd work as one surround speaker 'pair' electrically, maybe even sonically if you arrange them across the sides and/or rear. I'd experiment.

http://products.bose.com/pdf/customer_service/owners/og_161.pdf

You'll need a separate amp for any center or sub speakers.

Feb 03, 2011 | Pioneer Audio & Video Receivers

1 Answer

I used an instrument cord to plug my peavey citation in my cab an it worked great for 4 hours, then at the end of practice i noticed the volume was reduced by half


Most signal cables (guitar keyboard etc,) have conductors that are too light to handle the high current of an amplifier. Hopfully you did not hurt the amp. Get a real speaker cable

Dec 13, 2010 | Audio & Video Receivers

1 Answer

My Behringer gx212 ultratwin amplifier started to lose volume last night at band practice and then I smelled buring wiring. I think I lost or am in the process of losing the amp transformer. I think the...


Hi I just recently purchased a Behringer GMX 212 and had similar volume dropout on the clean channel only Channel 2 works better and has more punch in clean mode.I went to the shop where I purchased it with a 7 day warranty from some indian dude here in Nadi Fiji, and there was another GMX 212on the floor so I decided to try it out. This was a new amp. I plugged into the clean channel and turned it up full volume on guitar and amp adn heard the volume drop of in the amp in almost a curve and then the whole amp just cut out. We unplugged and waited, turned the amp off, and then on and stil no sound. We then tried the guitar and cord in another amp. The other amp was fine. Can you solve this problem.......my gut feeling is this happens a lot to Behringer amps.

May 08, 2009 | Audio & Video Receivers

1 Answer

My peavey ul 115 bass bin will only work through its bi amp input. Why is this ?. The other one works fine but when I switch speakers I have the same problem. Can you help please ?..Thank you.


The bi-amp jacks bypass the internal crossover. You need to look at the crossover section and see if an internal protection fuse has blown or if hte crossover itself is smoked.

Dan

Mar 04, 2009 | Audio & Video Receivers

1 Answer

The footswitch for bugera 6262 valve amp seems to have a logic problem. The clean channel leaves 'lead and reverb' leds lit on footswitch, pressing 'lead' lights the crunch channel on the amp... and reverb...


Hi ! Check and make shure that the cord conections between the pc board on the backplate of the amp to the logic board are firmly pushed in there slots.
Good luck , Stefan from Sweden

Aug 18, 2008 | Audio & Video Receivers

1 Answer

The channel select button on my Peavey Transtube/Delta Blues footswitch won't work. When plugged into my Bandit 112, only the effects button was working. The pedal is brand new.


please try to apply a lubricant contact cleaner on select button and press it many times(you can get contact cleaner from radio shack near you)

Jul 22, 2008 | Audio & Video Receivers

1 Answer

Have a peavey-xr-600b peavey mixer amp. i get aloud hum and noise and cracking when plugging speaker jacks.


Hi chillin884

Not a good sign. Something has gone wrong with the output stages of your Peavey. It is not a good idea to continue plugging it in as damage may occur to your speakers. I suggest you take it to a decent music gear repair guy for a look see and give you a quote to repair These heads, like all Peavey gear, are pretty solid and worth repair. Sorry to be the bearer of bad news like this, good luck

regards
Graeme

Jul 15, 2008 | Audio & Video Receivers

1 Answer

PEAVEY TRANSTUBE AUDITION 110. PLUG UNIT IN POWERS UP . SITS THERE AND HUMS LOUDLY. SPEAKER WORKS. plug guitar in can hear it faintly, push lead chanel button in , hum gets super loud. HUM IS IN PROPORTION...


There should be an 8 pin IC close to the input jack that will be marked 4558 or 4560. This is an Op-amp Ic that is the most likely cause of the problem. Replace that IC and report the results here.
Dan

May 27, 2008 | Audio & Video Receivers

3 Answers

Two amp


I don't know why you'd set the Peavey to 2 ohm to drive 8 ohm speakers??? My other thought is... I wonder if the phase is correct. try reversing one of the speaker wires Left or right side.

Geno

Feb 27, 2008 | Harman Kardon AVR 630 Receiver

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

461 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68223 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...