Question about Projection Televisions

1 Answer

I get sound but no picture. All I see on the screen is a line, a straight line.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I did not fix the problem, I did not know that I would have to pay for some advise. I could see paying if you had to come here and fix it or if I had to bring the TV to you. I will just get a new set in a few weeks. Thank you.

Posted on Apr 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Screen problems on my sylvania rear projection tv.....


If the lines are not actually in the picture but on the screen it may be if they are straight fine tape used around the inside edges of the screen---if in the actual picture a different story.

Aug 27, 2012 | Sylvania OSRAM RCA HDLP50W151YX4...

1 Answer

Picture problems


Is it one color that has moved? Sounds like a convergence problem. Find a channel with a fixed picture, or if you have digital cable or satellite pull up a guide, something with a straight line across the screen. You will likely see one of the colors is bowed or or shifted. You may be able to adjust that with your remote under the "convergence" adjustments in the menu. If it will not adjust it will need work done to the convergence circuit. Not a DIY project.

May 24, 2010 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

Toshiba 51h84 "Crooked Picture"


Still the convergece prob.The FL231 fuse near the FBT transformer it dead.The square fuses 3 rectangles fuses.One in the middle.

Aug 09, 2009 | Toshiba 51H84 51" Rear Projection...

1 Answer

Screen


HI, need to see a picture of the line and need to know if you see it on all inputs and whitch ones are you using and does it do it on all of them.
If you cannot send me a picture then let me know what color is the line,is it from left to the right end of the screen and the top and the bottom of the line are they straight all the way horrizontally.
Wait your response then I will do my best to find the solution.

Sep 13, 2008 | Sony Grand WEGA KDF-50WE655 50" Rear...

1 Answer

No picture


Sound like you lost Vertical Deflection.  Youshould not have a line across the screen because this could destroy the threeCRT Red, Green, and Blue (Picture tubes) if left on to long. There is a protection circuit built in to protect your CRT’s.    Check on the PCB-SIGNALboard (Tuner located on this board) transistors Q-206 Collector should be around 1 Volt Base and Emitter 0V. If the voltage atthis point is greater then 5 Volts the Vertical output IC-401 (Mounted on heat sink 7 pin inline IC) is bad, Part # LA7845.  Pin Voltages should be PIN 1= 0V, 2= 34V, 3= 32V, 4= 3V, 5= 3V, 6= 33v, 7= -6V.  Data sheet located at http://pdf1.alldatasheet.com/datasheet-pdf/view/40357/SANYO/LA7845.html

Jun 22, 2008 | Mitsubishi VS-6043 60" Rear Projection...

1 Answer

Magnavox 9p6040


Sounds like a solder or connection issue on the small signal panel. which is the ciruit baord on the left hand side of the set looking in from the rear of the set.

Jun 13, 2008 | Philips Magnavox 9P6034C 60" Rear...

1 Answer

Showing black screen with a blue line


Is the blue line running straight across the middle of your screen? If so its a vertical deflection problem. Possible bad Vertical output IC

Feb 20, 2008 | Panasonic PT-47WX53 47" Rear Projection...

1 Answer

Looks like pen marks on inside of screen


What you are decsribing sounds like your picture tube or tubes have been scored (permanent burn marks on the picture tube phosphor). The sure way to tell is to remove the front screen and look into each of the three lenses while the set is on. You will see a black image of your pen mark within the picture. Did you recently have problems with convergence or the set shutting down (turing off by itself for no resaon) ?

Nov 12, 2007 | Toshiba 50H82 50" Rear Projection...

1 Answer

My Hitachi 65SWX20B Model, made in 02, just developed Picture disturbance


Can you post a picture of the set. This might be a convergence problem. seeing the set will confirm this.

Thank you,
shuttle83

Oct 28, 2007 | Hitachi 65S500 65" HDTV-Ready Rear...

2 Answers

Mitsubishi cs-35401television


HORIZONTAL FAILURE AND LINE DOWN THE SCREEN. REPLACE T5A1 LOCATED ON PCC-3-PCB. PT#349P145030(FOR CS-35401,CK-35402 ONLY) Hope this helps! Troy

Sep 11, 2007 | Projection Televisions

Not finding what you are looking for?

Open Questions:

Projection Televisions Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...