My Bissell Proheat2 Model 9200 does not spray cleaner. I took all the hoses(tubes) off and cleaned them. They had the dried cleaner in them. Still does not spray. Could it be the pump?

Here is the Service Guide. Plumbing Guide is on Page 22.

https://evacuumstore.com/images/proheat-2x-service-guide.pdf

..

Go to www.bbay.dreamhost.com/bissel_proheat_2x_plus this guy took photos as he tookk it apart.

Assuming this is the pro heat version
Most likely you have some debris blocking the system. You need to follow the hand tool cleaning instructions.
remove the hand tool and manually wash it
select the tools cleaning option
place the tube in a bowl of clean water and allow it to **** the water up - this should clean out any blockages in the pipe.

Hi,

Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101

Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101

teyet

Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101
bnv,nm

Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101

hjghkl

Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101

rtetrhgd

Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101

fkj

My Bissell also STOPPED SPRAYING WATER.

I've owned a Bissell 9200 for a few months. I've used it twice, the last time most likely being around August. I attempted to use it this past weekend and it wouldn't spray. I searched all the help sites I could find and thought the solution was a clog in the heater, which many said was located in the arm. After I took the arm apart, to my surprise, THE HEATER IS NOT LOCATED IN THE ARM OF THE 9200 MODEL.

It's still under warranty, however am not located near a service center so I took it upon myself to try to fix it.

I'm just a single female who ends up trying to fix a lot of stuff herself so, I don't speak "technical instructions". But, here's what I did in the event that it may help someone else.

I unscrewed all the screws that I could on the base. I removed the cover over the motor. Doing so revealed the hoses attached to the soap dispenser. Located closer to the rollers were more hoses. On the same side as the foot lever, above the wheel is the where the HEATER is located.

Being that I was looking for a clog, I unclamped one hose at a time; inserted a safty pin into what the hose was attached to and wiggled it; re-clamped hose afterwards.

The only slight confusion may be with the screws. There are only two sizes. I used finger nail polish to mark where the small ones went.

I reassembled it, turned it on, and it actually started spraying again!!!!!!!!

So that this "blockage" won't occur again, I will take advice I've read about cleaning Bissell's hoses out after using it.
See, taking the thing apart was really nerve racking! Especially not knowing if it would even work after I put it back together.

GOOD LUCK WITH FIXING YOUR CLOG!....you'll probably need to sooner or later.