Question about Montgomery Ward (223600UP) Heater

Open Question

Mongomery ward-top vent wall furnace # sfb 50175ac (1977)

Trying to locate the pilot light for this furnace, is there a special hidden place for this?

Thankyou,

Angela

Posted by on

2 Suggested Answers

  • 66 Answers

SOURCE: MW wall heater SFB-50145B, SN:HD47X, 50k BTU

Depending age of unit, clean either the thermocouple, or the flame sensor.

Posted on Feb 22, 2010

james3751
  • 614 Answers

SOURCE: how do i light the pilot on a ward floor furnace

You need a very kong wire and a kitchen match. Turn the knob on top to pilot and push down have your flame already down thru the pilot hole at the bottom of the inside of furnace. Hold for a few seconds and release knob trun to heat. This unit works on a power pile systm and generates milivolts from the flame. Rus

Posted on Dec 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Williams wall heater 2509622. How do I keep the pilot on? It tends to turn off after it reaches the desired temperature.


WILLIAMS 2509622 OWNER'S MANUAL Pdf Download.

www.manualslib.com > Brands > Williams Manuals > Furnace > 2509622
2509622; 2539622; 2559622; 3509622; 3539622; 3559622; ... WHAT TO DO IF YOU SMELL GAS: ... Williams furnace co. direct-vent wall furnace owner's manual (24 pages) ... Caring for Your Furnace ............24-25 Locating Wall Furnace and Thermostat ........6-7 Learn how to keep your new Williams Furnace operating.

How to light Heater or Furnace Pilot Light Gas Pilot of ...

? 5:01
https://www.youtube.com/watch?v=FZVQmKTYTTg
Oct 25, 2013 - Uploaded by 3p0cHx
How to light a gas pilot for a heater or furnace of the Williamstype. This is a general guide and is not ...

[PDF]Monterey Installation Instruction Manual - Home Depot



Dec 08, 2015 | Williams Heaters

1 Answer

Just need to know how to light the pilot on a Montgomery Ward wall furnace model sfb-50219


I can't speak to the specific model but with most pilot lights, there is a switch setting or button for lighting. If you release that switch or button too soon, the pilot will not remain light. Hold the switch or button ON while you light the pilot. Keep holding the switch or button for about a minute until the heat sensor is sufficiently warmed that the pilot light stays on. Good luck.

Nov 13, 2014 | Heaters

1 Answer

Cant figure out how to relite my furnace


on the bottom of the unit there is an access door remove it and behind it you will find a gas valve and a pilot find the piolot......turn off the gas valve and move the selector to piolot depress the switch and at the same time place the flame from a log lighter onto the pilot light after this lights turn the gas valve to run and the burner should light.

Mar 03, 2011 | Empire Direct Vent Wall Furnace;...

1 Answer

How do I turn on my superior ventless fireplace


I'm not sure about that brand, but I finally figured out how to turn the one in the house I just moved into. The only visible control if you have not accessed the fireplace controls before is the switch on the wall. The wall switch is strictly an on off switch, but it only works if the pilot light is already lit, and the pilot light will not go out by turning off the wall switch. To access the controls, first pull out the vent covers, they are simply held in place with pressure buttons on each end. Behind the lower vent are the controls for the pilot light and fire intensity, mine also contained a metal plate with the instructions printed on it. Open the glass door by opening the four latches, two on top and two on bottom, and then swinging it out on its hinge. You will find the gas spout for the pilot light hidden between the logs. Turn on the main gas line by turning the straight edge of the red handle parallel with the gas line. Turn the gas control to pilot, by pushing in and turning, and then push in all the way to start gas flowing. I like to have a match already lit next to the valve when I start the gas. After the pilot light has been on for about 60 seconds let go of the button and it will return to its normal position. Then turn the control to on and turn on the wall switch, the main burners should start lighting. Close the glass and put the vent covers back in place and your ready to enjoy the fireplace :)

Nov 27, 2010 | Heaters

1 Answer

How do i light the pilot on a ward floor furnace madel 570 edr


You need a very kong wire and a kitchen match. Turn the knob on top to pilot and push down have your flame already down thru the pilot hole at the bottom of the inside of furnace. Hold for a few seconds and release knob trun to heat. This unit works on a power pile systm and generates milivolts from the flame. Rus

Dec 13, 2009 | Montgomery Ward (223600UP) Heater

1 Answer

Wall furnace model # SFB50146B Thermal Coupler. Does it have 2 wires?


if the pilot light stays lit, but the burners don't kick on, it's a problem with the thermostat or thermostat wiring, or a problem with the valve inside the gas actuator

Oct 24, 2008 | Montgomery Ward (223600UP) Heater

4 Answers

Williams wall furnace, top vent.


I've replaced a Williams wall gas heater non-electric. The thermostat is connected right and mounted on the wall. But, there's a thick black copper wire on the side of the furnace tagged thermostat. I don't know what to do with it? Where do you connect this wire? When it touches the top screw of the three screws running vertically(where the other wires are connected). The burner lights up and stays on, even if you play with the wall thermostat. Touching the other two screws doesn't do anything. Now, the manual talks about connecting it to the venting wires? Extra wires coming from the top or maybe somewhere else in the wall? I've left it connected to the first screw, ran the heater. But, it never turns off? Any suggestions? Thanks

Dec 13, 2007 | Heaters

1 Answer

Williams gravity vented wall furnance - where is the pilot?


Its in the bottom of the heater behind the vent cover . I don't know where you are but your local gas utility will come out and lite this for free.

Dec 10, 2007 | Williams 2509612 Ceramic Mid-Size Heater

2 Answers

Unable To Keep Pilot Light Lit!


I have a Williams top vent gravity wall furnace (model 5009622) and I had the same problem. I had to take the cover off the furnace -- screw on top and two at the bottom (open the access door and there is one screw on each side) to get to the reset button for the vent safety shutoff system. On my furnace it's on the left side toward the top of the unit. I pressed the little red reset button and it's been working ever since. If your furnace is properly installed and doesn't have bird's nest in the chimney, it should work fine. Good luck!

Mar 04, 2007 | Williams 2509612 Ceramic Mid-Size Heater

Not finding what you are looking for?
Montgomery Ward (223600UP) Heater Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Montgomery Ward Heaters Experts

paulcarew

Level 3 Expert

1915 Answers

Mack Baxter

Level 3 Expert

379 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Montgomery Ward Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...