Question about VCRs

1 Answer

VCR Error I have 2 TEAC VCR's Model MV6092 which has an error code RF26 appearing? Model 3090 which has error code RF22 appearing? Could you please tell me what these codes mean. I have a teac MV-6092 which displays error 'RF 26' also, any help would be appreciated

Posted by on

1 Answer

If u dont have a remote for these, it is just the programming setup, i have same prob, but because I dont have a remote I cant get past it

Posted on Aug 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi i am getting error "Er:03" on the VCR screen. Cant FF/RW/play/eject.


Possibility of mechanism fault inside the VCR, which might include tape damage. Can't answer directly about the 03 code, without knowing make or model number as they all use different fault codes.
Taking the top cover off might show up what's happened.

Nov 21, 2015 | VCRs

1 Answer

Error code 31:33


This type of error code ,will happen if ur have a voltage problem MD 76 board (tape sensor) .Error coming when u put STD tap or MIN tap?.Can u check the this two cable CN 1 and CN 2 MD 76 board.

Apr 25, 2013 | Sony DSR-45 Mini DV VCR

1 Answer

Mitsubishi VCR Model HS-821V Ejects Video Cassette & gives an error code E4


Sometimes things like that are caused by the mode switch which will either need to be cleaned or replaced. It's worth looking inside for damage inside the unit. Pay close attention to plastic parts.

Nov 26, 2012 | VCRs

1 Answer

F03 DISPLAY ON MY NV-SD300 PANASONIC


go to panasonic.com/vcr and give them the model/serial # and ask what the F03 error code means and they can give you a solution for the problem.
Jerry

Aug 27, 2012 | Panasonic VCRs

1 Answer

Error E3 on Mitsubishi HS-U795


Try this :
If your VCR malfunctions, try the following steps prior to contacting your Mitsubishi Dealer:
1 Check the Trouble Checks below to see if there is a solution to the current problem that you are
experiencing.
2 If the problem is not addressed on the Trouble Checks, the safety circuits in the VCR may be in
operation, thus please try the following: (the clock setting and the timer recording will be deleted.)
1 If possible, press EJECT on the front panel and remove the tape.
2 Press TIMER RESET on the rear panel with a pencil or a ball point pen.
3 If a tape is not loaded, press POWER to turn the power on. If a tape is loaded, wait about 1 minute
until the tape protecting function is completed, then press POWER.
3 You may also try the following procedure if the above steps did not resolve the problem (All settings will
be reset to the default settings.).
1 Press POWER on the front panel continuously for about 8 seconds until the current time display on
the front panel shows "- : - -."
2 If a tape is not loaded, press POWER to turn the power on. If a tape is loaded, the tape protecting
function will work and "99" will appear on the front panel display to begin count down. Wait about 1
minute until it reaches "00" to show the tape protecting function is completed, then press POWER.
If the problem with your VCR persists, contact your Mitsubishi dealer for assistance.

Im looking for error codes.

Mar 10, 2008 | VCRs

1 Answer

REP error.


Short for "repair"..accordianman

Feb 21, 2008 | VCRs

3 Answers

Vr540 philips


Error 2 and error 3 and error 4 are tech codes.
and if your unit won't reset, you can take it to your local
electronic repair shop. I had error 3 on my Phillips,
and he went to the PM webpage,researched it, and fixed it perfectly for $39.00 total. STILL WORKING!
He said it was some little thing to replace that took him 15 minutes.
If you don't want to buy one of the REALLY cheaply made vcrs or DVD/vcr combos that are out now, it worth a little phone time to find
an electronics repair shop. Or the new DVD recorders with vcr combos are very good, but sturdy ones are expensive.

Dec 25, 2007 | Philips VR540 VHS VCR

2 Answers

Vr540 philips


E2 is not an error code. It means that the video tuner is set to EXT2 (Scart input 2)

Press the VCR button on the remote control, and try again.

Nov 17, 2007 | Philips VR540 VHS VCR

Not finding what you are looking for?
VCRs Logo

Related Topics:

397 people viewed this question

Ask a Question

Usually answered in minutes!

Top VCRs Experts

 Grubhead
Grubhead

Level 3 Expert

4590 Answers

alexander woolfolk
alexander woolfolk

Level 2 Expert

276 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a VCR Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...