Question about Adaptec 2610SA (0H2052) Serial ATA Controller

1 Answer

Hi. We have a ML110 server with RAID 5 (4x250gb HD SATA) in a Adaptec 2610SA. The RAID has 2 Arrays (#00 Operating System and #01 Data). We have tried to replace a failed HD and since then the Windows cannot start. It shows us that the Array #00 cannot be configured (following arrays have missing required members and cannot be configured). Array #01 Data seems to be ok. Any clue ?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 260 Answers

Did you make sure that your hard drive has been made into a "dynamic volume" instead to the usual "simple volume"? It has to be "dynamic" before your can put it into a RAID configuration. You will have to use your RAID Controller to create a dynamic volume or to make the hard drive part of a dynamic volume.

Posted on Aug 04, 2010

  • 1 more comment 
  • dudabhz Aug 04, 2010

    The new HD is a brand new direct from HP. At this moment the Array #1 (Data) is in rebuilding process (32 % so far). But I cannot "see" the Array#0 (Operating System). I will wait until the rebuilding of the Array#1 of the RAID is done to see if the Array #0 returns... If not, do wyou think I can try to recreate the Array #0 for this RAID ? I have the information about the Array #0 (Size, Stripe, Type).

  • madhatter639
    madhatter639 Aug 04, 2010

    You may be able to, but that will most likely exceed my scope of experience. If its in the rebuilding process, then I would assume for now that everything will be fine once its finished rebuilding Array #1.

  • dudabhz Aug 04, 2010

    Ok. Thanks a lot. I'll let you know as soon as it ends. I think just tomorrow. Thanks

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Operating system corrupted how to recover the data


RAID is only to protect data in case of hard drive failure. Data is only recoverable from backup.

However, if you have a separate arrays for the OS and data. Meaning two arrays, you can swap arrays onto an identical server with same array configuration. Drive positions (bay /slot) are critical.

Oct 01, 2012 | IBM x3400 Server

2 Answers

Dell Precision 670 RAID1 Install on Windows 7


The RAID configuration maybe setup in the BIOS settings.

Mar 31, 2012 | Dell Precision Workstation 670 PC Desktop

1 Answer

I have got a 3 disk raid5 IBM xseries Server which does not boot. How can I resque data from these disks?


I'm going to go out on a limb and assume that you don't have a good backup of the data on your RAID array. So, generally speaking, the operating system is probably installed on a separate disk from your raid array (not a guarantee). But if this is so then you should be able to reinstall your operating system and drivers (esp RAID controller) to that (separate) disk and you're off to the races (replace this system disk if necessary). -OR- Depending on the make of your RAID controller you may be able to transplant your RAID controller into another machine and all the original drives along with it, so long as it has a battery backup and you place all the drives in their original order. If there is no battery backup on your RAID controller then DON'T PULL THE PLUG ON THE ORIGINAL MACHINE AND DON'T EVEN CONSIDER removing the RAID controller in any way. If you have any doubts, whatsoever, have someone with experience in RAID arrays do the work for you. It will be well worth it! (RAID arrays aren't for the faint of heart)...

Aug 24, 2011 | IBM eServer xSeries 225

1 Answer

I have an Intel® Entry Server Board S875WP1-E with Adaptec SATA raid on board. We replaced the existing wd 74 Gb hard drives after 5 years of good service. Replaced with seagate 500Gb NS series drives...


1st check what is the file system of the 75GB hd
is it on NTFS or FAT system

after you find what is it then format the 500Gb with the same file system with that of the 75GB

Jan 03, 2018 | Intel Server Board S875WP1-E Motherboard

1 Answer

Dell RAID controller in HP server? Hi i have dell (Adaptec) CERC SATA1.5/6ch RAID card, now i want to use this card in HP proliant ml150 g3 server, after fixing this card server did not recognize it keeps...


This particular device will require drivers for the Operating System to use. Also the hard disk drives will have to be installed an initialized outside the Operating System first before use. This is usually during startup after the system BIOS.

The exact steps can be found on the RAID card manufacturer's web site.

Feb 18, 2010 | HP ProLiant ML150 G3 Server

3 Answers

Boot problem with IBM xseries 206 - SCSI Drive and SATA drive


Refer to user's manual how to set the boot order in BIOS.

Jul 17, 2009 | IBM eServer xSeries 206

1 Answer

HP Proliant ML110 Server RAID setting


if you have the RAID 0+1 or 1 ,beacause of the mirroring ,2 disk will be the same.you should be attention ,if you transfer data on the first disk,you must boot your server with that disk.when the system boot completely then you put the second disk ,beacause of the Raid 0+1 or 1 the data of the first disk automatically write on the second disk.

Jun 24, 2009 | HP ProLiant ML110 Server

1 Answer

SCSI BIOS not installed / ML150G2, exchanged mainboard, RAID


hi..
my guess is no but since i haven't dealt with this type of server i'm going to suggest you go to hp.
if you just goto hp.com and search on live chat and a link will come up.. they should be able to help unless it's too old since i'm not sure what generation we are on now..

good luck, hope this helps a little..d

Feb 23, 2008 | Adaptec (2120S) SCSI Controller

Not finding what you are looking for?
Adaptec 2610SA (0H2052) Serial ATA Controller Logo

Related Topics:

577 people viewed this question

Ask a Question

Usually answered in minutes!

Top Adaptec Computers & Internet Experts

Rommel Balcita

Level 3 Expert

749 Answers

Robert Graf

Level 2 Expert

250 Answers

Timothy Van Der...

Level 2 Expert

135 Answers

Are you an Adaptec Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...