Question about RCA R52WM24 52" HDTV Projection Television

1 Answer

Broken screen question

How do you take off the front panel to get to the borken screen? Does it just pop off?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 76 Answers

I'm sorry, that is a broad question because the answer may differ from brand to brand and from one model to another. If you contact an authorized service center, one of their technicians may be able to answer this. Just remember that once you replace the screen you should fine tune the convergence for optimum picture quality.

Posted on Apr 27, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

We have a broken back screen on a sharp 60" aquos. Can this be repaired for a reasonable price?

If the screen is borken, there is no repair to it. Should be replaced.

Jul 05, 2014 | Televison & Video

1 Answer

Tv screen broken

If the protection glass in front of the TV only have borken, it can be replaced. If the screen as a whole has broken, there is no other way than replace the screen, which will cost around 2/3rd of the total cost of a new TV. Check this link for details. It has disassemble procedure to many brand Plasma TVs, with illustrations. You can get an idea about how the screen is fitted, and what is the protection glass and actual plasma screen. Pull up previous posts there, either by its left side bar, or view it in Timeslide option.

Jul 03, 2013 | Samsung 43 PN43D450A2D Plasma TV

1 Answer

Estate dryer will not heat. Does not even start to heat up.

You could have a broken igniter element. to trplace this you must first remove the front panel. To do this remove the lint screen and you will see 2 screws, remove them - next take a broad blade putty knife and insert aproxametly 1 to 2 " where the top meet the front panel on each side and the top should pop up, next rempve the 2 screws on either side of the front panel and the front panel will remove. Down at the opening of the funnel you will see a ceramoc disk with an element attached if this is broken that is why you do not see the glow.

Feb 01, 2013 | Dryers

1 Answer

Switch on 1987 toyota pickup cool to heat broken

Tear it apart and see what is borken is all the advice i can offer.

Nov 01, 2012 | Toyota Cars & Trucks

1 Answer

I replaced the lower scan board (SDR D) and I just installed it but its still blinking 4 times. DO you think the SDR U is also borken? Please advise.

I just got through pulling my SDR-U out and the blue led stopped blinking and the bottom half of screen lit up.Heard a pop and the screen went off and now it blinks 3 times instead of 4.Technical person told me to check for blown cap on Y sus board,if it did it again to replace the Y sus along with SDR-U.Hope this helps,I think I know what to do now.These boards are hard to find think I'll try to find someone to repair them through mail.

Jun 23, 2011 | Hitachi P50H401 50 in. Plasma HDTV

2 Answers

My husband fell into the television and the front screen popped out. Can we put it back in ourselves? It is not broken

You should be able too. You will need a torx #20 driver bit to remove the bezel around the screen. Carefully... The screen can be easly scratched

Oct 22, 2010 | GE D52GW12 52" Rear Projection HDTV-Ready...

1 Answer

Dropped my tv and now there are spider cracks in the screen.turns on but no picture

Sorry the LCD screen panel are damage and broken.The LCD screen panel are 90% of the tv.It limited produced,not worth repairing,if LCD screen panel are borken or damages.It will,cost the same as a new tv,if requiring to replaced the LCD screen panel.Sorry,now,ur tv does not worth as a whole tv anymore.Only worth as salvage tv for spare electronic boards for parts,that it.

Oct 01, 2010 | Proview PA40JK1A 40 in. LCD Television

1 Answer

Borken on/off switch. It is down and will not

please sell it for me your laptop gateway mx7122 my email is

Oct 03, 2009 | Gateway MX7122 Notebook

1 Answer

The screen is borken

you need more details then that. lol if your screen broken then you need to buy another one..

Aug 18, 2008 | Sony PlayStation Portable (PSP) Console

1 Answer


My SA-AX710 overloads intermittently. The problem is a broken solder joint between a pin on one of the power transistor modules and the circuit board. To fix it, I removed the circuit board from the case and resolder the borken joint. Opening the case is easy. First remove the top of the case. Then remove the 3 screws in front. The front panel can then be pulled off. After that, remove all screws holding the connectors on the back. The circuit board can be detached from the case by removing the screws from the top of the board. Broken solder joint is probably one of the most common problems with modern electronics.

Mar 03, 2008 | Technics SA-AX710

Not finding what you are looking for?
RCA R52WM24 52" HDTV Projection Television Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74887 Answers


Level 3 Expert

905 Answers

matt martin
matt martin

Level 3 Expert

1213 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides